Coleman 2000 Serie Instructions De Montage page 2

B Y B A
EFORE OU EGIN SSEMBLING
Y N Q C
OUR EW UALITY
G B G
AS ARBECUE RILL
FOR EASE OF ASSEMBLY, leave the grill on
the inside bottom foam packing tray until the
wheels have been attached. (See representative
example at right). Remove the outside foam from
the right and left sides of the frame base at this
time.
Remove all cartons located on top of the barbecue
grill base and set aside.
S C
TART THE OOKING
S P
EASONING ROCESS
A Y
SSEMBLING OUR
C I G
AST RON RIDS
Cast Iron grids are on select models only.
Your cast iron grids may have some rusting.
This is normal. To remove the rust, scour the
rusty areas with steelwool, i.e. SOS pad, until
all traces of rust are gone. Wash, dry and
season grids.
S C I
EASONING AST RON
S
EASONING IS THE PROCESS OF ALLOWING OIL TO BE
,
ABSORBED INTO THE IRON CREATING A NON
. H '
RUSTPROOF FINISH ERE S HOW TO DO IT
Preheat Oven to 350ºF.
Wash with hot, soapy water and a stiff brush.
Rinse and dry completely.
Oil the grids (all surfaces, top and bottom) with
MELTED solid vegetable shortening.
Turn upside down on the top rack of a 350ºF
pre-heated oven.
Put aluminum foil on the bottom rack to catch
any excess drippings.
Bake the grids for one hour at 350ºF.
Let the grid cool slowly in the oven.
Store, uncovered, in a dry place when cooled.
OLEMAN
:
G
RIDS
B
EFORE
G !
RILL
C
ARTON
Two Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(16)
Two Main Control Knobs . . . . . . . . . . . . . . . . . . . . . . . . . .(32)
One Grease Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(49)
One Grease Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(49a)
G
RIDS
Two Grease Drip pans . . . . . . . . . . . . . . . . . . . . . . . . . . .(48)
One Perforated Tent . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(62)
- ,
One Meat Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(57)
STICK
One Meat Probe Receptacle . . . . . . . . . . . . . . . . . . . . . . .(57a)
:
One Handle Assembly
One Literature Bag
One 6-lobe Screwdriver
Hardware bag(s)
Assorted assembly hardware - One Igniter Kit bag
Two Axle pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(3)
Side Burner Models include the following:
One Side Burner Control Knob . . . . . . . . . . . . . . . . . . .(40)
Combustion by-products produced when using
this product contain chemicals known to the State
of California to cause cancer, birth defects, or
A - M P
ISCELLANEOUS ARTS
WARNING:
other reproductive harm.
Tools Needed
#20 6-Lobe Screwdriver (Included)
#2 Phillips Screwdriver
An adjustable wrench
9-Volt Battery (Included)
Optional Tools
7/16" and 5/16" Box End Wrenches
7/16" Nut Driver
Electric or Cordless Screwdriver
#20 6-Lobe driver bit
#2 Phillips driver bit
O C - L.P. G
NE ARTON AS
C B - 2 S
ARTON IDE
A
SSEMBLIES
(F M W S
OR ODELS ITHOUT
O R S T A
NE IGHT IDE ABLE SSEMBLY
O L S T A
NE EFT IDE ABLE SSEMBLY
C B - 1 S T
ARTON IDE ABLE
(F M W S
OR ODELS ITH IDE
O S B G . . . . . . . . . . . . . . . . . . . . . . . . .(41)
NE IDE URNER RID
O R S T A
NE IGHT IDE ABLE SSEMBLY
O L S B A
NE EFT IDE URNER SSEMBLY
One bag Assorted assembly hardware
O C -C S
NE ARTON OLEMAN
A
SSEMBLY
(F M W S
OR ODELS ITH IDE
Engineering Code
LD113332/LD113312
LE113332/LE113312
LE113333
LD113342 * /LD113322 *
LE113342 * /LE113322 *
LE113343*
*Cylinder not included
11412013FX (Pg. 2)
C
YLINDER
T
ABLE
B )
IDE URNER
A
SSEMBLY
B )
URNER
B
IDE URNER
B )
URNER