Panasonic DVD-LX9 Mode D'emploi page 23

Troubleshooting Guide
Operation
The unit doesn't play the Reload the disc for the setting to be effective. Open and close the
data type (WMA/MP3 or disc lid, then press [1] (Play) to start play.
JPEG) selected in the
"Mixed Disc-Audio&Stills"
in the SETUP menu.
Sound
There is a lot of noise. ≥Move unit away from mobile phones.
No sound from the ≥The speaker is off if the LCD is closed or headphones are connected.
unit's speaker. ≥Turn up the volume. @
No sound from other ≥Check all connections and settings. S–U, X, Y
speakers. ≥Check input mode of the other equipment.
Distorted sound. ≥Advanced Surround may cause distortion with some discs.
Turn Advanced Surround off if this occurs. M
≥Output from this unit will be in stereo (two channels) when Advanced Surround
is on. Turn Advanced Surround off if you are using three or more speakers. M
≥Some DVD-Audio specify the number of channels to be played and prohibit
down-mixing to 2 channels. Read the disc's instructions for details.
≥Press [1] (Play) to restore normal play after changing the speed. P
≥Noise may occur when playing WMA files.
SD There may be some noise output when playing MPEG4 and
≥
VOICE files, but this is normal.
Sound effects do not ≥Dialogue Enhancer and Advanced Surround do not work when the
work. unit is outputting bitstream signals.
≥Advanced Surround does not work if you have changed the play speed. P
Picture
The LCD is dark. ≥Adjust the brightness. O
Picture distorted. ≥Some disruption is normal during SEARCH.
Picture quality may worsen or some frames may be skipped
≥ SD
when viewing MPEG4, but this is normal.
Menus not displayed ≥Restore the zoom ratio to k1.00. R
correctly. ≥Set the subtitle position to 0. N
≥Set "4:3 Aspect" to "Normal". R
No picture on the LCD ≥Select a picture mode other than "OFF" (no picture). O
Picture from another ≥Check connections. U
unit not shown on the ≥Ensure the input setting is correct. U
LCD. ≥Ensure the power of the connected equipment is on.
Picture doesn't appear ≥Check connections. T, U
on the television (or ≥Check that the television is on.
the size of the picture ≥Check that the input mode on the television is correct.
seems wrong). ≥Check the settings in "Video—TV Aspect". W
≥Use the television to change the aspect to the correct one. If your
television cannot change the aspect when input is progressive,
try changing 4:3 Aspect with the on-screen menu icons. R
≥Turn off the zooming feature of your television if you are using Variable Zoom. R
≥Ensure that the unit is connected directly to the television, and is not
connected through a video cassette recorder. T
There is ghosting ≥Change "Video output mode" to "480I". This problem is caused by
when progressive the editing method or material used on DVD-Video, but should be
output is on. corrected if you use interlace output. R
LCD pixels turn black ≥The LCD is constructed with precision technology so 99.99 % of the pixels
or radiate different are active, but of the remaining of 0.01 %, there are pixels that may be
44
colors. black or emit light constantly. This phenomenon is not a malfunction.
Displays
On-Screen Menu Icons ≥Use [3, 4] while the Bar position icon is highlighted to move them
are cut off. down. P
No On-Screen display. ≥Go to the Display menu in the SETUP screen, and select "On" for
"On-Screen Messages". X
"Check the disc." ≥Clean the disc. 9
"The progressive out is ≥Go to Video in the SETUP menus, and select "Enable" in
set to "Disable"" "Progressive Out (Component)". W
"X" ≥You are trying to play incompatible or corrupted data. This data
cannot be played.
"CHECK CARD" ≥The card cannot be played.
"NO FILE" ≥Data the unit can play is not recorded on the card.
"PLEASE ≥Turn the unit off and on again. Alternatively, turn the unit off,
RE-OPERATE" disconnect the power source (AC or battery pack) reconnect the
power and turn the unit on again.
" ERROR 01" ≥A problem has occurred with the battery pack. Consult your dealer.
" ERROR 02" ≥The battery pack has been recharging for 12 hours but has failed to
recharge for some reason. Recharge again.
" ERROR 03" ≥You are recharging in a location that is too hot or too cold.
Recharge at normal temperature.
"H ∑∑" ≥Trouble has occurred. The number appearing after H depends on
∑∑ stands for a the problem. Turn the unit off and on again. Alternatively, turn the
number. unit off, disconnect the power source (AC or battery pack) reconnect
"U11" the power and turn the unit on again.
If the service numbers fail to clear, note the service number and
contact a qualified service person.
[Í] and [CHG] indicators
The [Í] indicator ≥The unit has malfunctioned. Consult your dealer.
flashes rapidly.
The [Í] indicator ≥The unit is on and the LCD is closed or the display mode is set to
flashes slowly. "OFF" (no picture). Turn the unit off when you have finished.
The [CHG] indicator ≥There is a problem with the battery pack. Turn the unit on and check
flashes rapidly. the message on the LCD (see above).
The [CHG] indicator ≥Battery pack charge is low. The unit will turn off automatically after a
flashes slowly. few minutes. =
Note
The following do not indicate malfunction.
≥Sound from the AC adaptor during recharging.
≥The battery pack warming up when recharging or during use.
≥The surface and area around the card slot becoming warm when used over long periods.
45