Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
TROUBLE SHOOTING GUIDE
T
R
O
U
B
L
E
S
Heater Will Not Light ;
. 1
F
u
l e
a t
n
k
s i
e
m
p
y t
2. Water present in kerosene
3. Igniter plug Fails to Glow
4. Igniter plug makes contact with
s
d i
e
f o
i w
k c
Heater Produces Smoke or Odor ;
. 1
F
a l
m
e
s i
o t
o
h
g i
h
2. Heater is in an air draft
. 3
B
u
n r
r e
s i
n
t o
e l
v
l e
4. Carbon or tar built up on wick
5. Contaminated kerosene
Flame Flickers or Dies ;
1. Water present in kerosene
2. Carbon or tar built up on wick
Wick Burning Down Excessively ;
1. Dangerous, volatile fuel
mixed with kerosene
(gasoline, benzene, alcohol,
white gas, paint thinner, camp,
stove fuel, oil compound)
Wick Adjuster Sticks ;
1. Water present in kerosene
2. Carbon or tar built up
Heater is enveloped in flames ;
C
O
R
R
water-clear 1-K kerosene or
. 1
F
l l i
a t
n
k
i w
h t
red dyed 1-K kerosene.
2. Drain tank. Remove wick assembly & replace wick.
Reinstall wick assembly. Fill tank with water-clear
1-K kerosene or red dyed 1-K kerosene.
3. Replace batteries if necessary. Be sure batteries are installed
properly. Replace igniter plug. Check for broken or disconnected wire.
4. Lower wick using wick adjuster knob until igniter plug
m
a
k
e
s
c
o
n
a t
t c
i w
h t
o t
p
f o
. 1
Using wick adjuster knob, lower wick to desired 1/2" flame.
2. Move heater out of air draft.
. 3
U
s
n i
g
b
u
n r
r e
k
n
o
, b
o r
a t
e t
seats properly over wick.
4. Perform "Carbon Removal / Dry Burning" procedure.
Replace wick if necessary.
5. Drain tank. Remove wick assembly & replace wick.
Reinstall wick assembly. Fill tank with water-clear
1-K kerosene or red dyed 1-K kerosene.
1. Drain tank. Remove wick assembly & replace wick.
Reinstall wick assembly. Fill tank with water-clear
1-K kerosene or red dyed 1-K kerosene.
2. Perform "Carbon Removal / Dry Burning" procedure.
Replace wick if necessary.
1. Drain and clean tank
Remove and replace wick
Fill tank with water-clear 1-K kerosene
or red dyed 1-K kerosene.
1. Drain tank. Remove wick assembly & replace wick.
Reinstall wick assembly. Fill tank with water-clear
1-K kerosene or red dyed 1-K kerosene.
2. Perform "Carbon Removal / Dry Burning" procedure.
Replace wick if necessary.
Call Fire Department.
Exit quickly and warn others.
DO NOT: Move heater, try to smother fire, or put water
on fire.
16
16
E
C
T
V I
E
A
C
I T
O
N
w
c i
. k
b
u
n r
e
f r
o r
m
s
d i
e
o t
s
d i
e
u
n
i t
t i l
Publicité
Table des Matières
Dépannage
