Memory Function - Makita CW001G Manuel D'instruction

A) When the appliance get equal to or greater than
30° from level angle as shown A in the figure, the
appliance shuts down and the temperature display
shows "F1" for a while. It takes 3 minutes to restart
after the appliance back in level position.
► Fig.4
B) When the appliance get equal to or greater than
30° from level angle as shown B in the figure, the
appliance shuts down and the temperature display
shows "F1" for a while. It takes 3 minutes to restart
after the appliance back in level position.
► Fig.5
C) When the appliance get equal to or greater than
30° from level angle as shown C in the figure, the
appliance shuts down and the temperature display
shows "F1" for a while. It takes 3 minutes to restart
after the appliance back in level position.
► Fig.6
D) When the appliance get equal to or greater than
30° from level angle as shown D in the figure, the
appliance shuts down and the temperature display
shows "F1" for a while. It takes 3 minutes to restart
after the appliance back in level position.
► Fig.7
USB charging
There is the USB port in the battery compartment. The
USB port continuously outputs 5V voltage in operation
state.

Memory function

After setting the control temperature, if the user does
not operate within 5 seconds, the current setting will be
memorized. Next time, the appliance starts in the same
setting.
Switching the unit of temperature
You can switch the unit of temperature °C (degree
Celsius) or °F (degree Fahrenheit) by following
procedure.
1. Turn on the appliance.
2. Press the cool / heat switch button until the unit
(°C or °F) starts flashing.
3. Press the temperature plus button or the tempera-
ture reduction button to select unit.
4. Press the cool / heat switch button, or leave the
appliance 5 seconds without any operation. The
unit selection is completed.
Shoulder belt
CAUTION:
Make sure the shoulder belt
securely attached properly. Otherwise falling acci-
dent may occur.
1. Put the belt through left and right handles.
2. Buckle the belt.
► Fig.8
Error code
For the specific errors, the temperature display shows
following code.
Error code
F1 Tilt protection is active. Refer the section for
the tilt protection function.
F2 Running out of battery.
F3 Input voltage is low. Refer the paragraph for
the car input protection.
F4 Input voltage is high. Refer the paragraph for
the over-voltage protection.
F5 Something is wrong with the sensor in the
appliance. Take the appliance to Makita
Authorized or Factory Service Centers.
MAINTENANCE
CAUTION:
Always be sure that the appliance
is switched off, unplugged, and the battery car-
tridge is removed before attempting to perform
inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Cleaning
• Clean the oil stain in the chamber regularly.
• Clean around the interior of the chamber to pre-
vent odor.
• Clean the dust on the sponge filter regularly to
improve the refrigeration efficiency.
• The sealing strip of the upper cover is easy to get
dirty, clean it in time.
Defrosting
To defrost, turn off the power and wait until the frost has
melted. Then wipe off the water.
Cleaning the sponge filter
CAUTION:
After cleaning the sponge filter,
be sure to install it on the appliance. Operating
the appliance without the sponge filter may cause
malfunction.
1. Slide the filter cover in the direction of the arrow
shown in the figure, and then take the filter cover
off.
2. Take off the sponge filter, clean the sponge filter.
► Fig.9
3. Install the sponge filter and the filter cover back.
► Fig.10
12 ENGLISH
Matter