Important - EINHELL TE-CN 18 Li Instructions D'origine

immediately each time after it has been used.
•
Each time before starting work, check that the
trigger catch functions perfectly and that all
screws are securely fastened.
•
Never tamper with the stapler.
•
Never dismantle or block any parts of the
stapler such as e.g. a trigger catch.
•
Never carry out any "emergency repairs" with
unsuitable means.
•
Proper stapler maintenance is required at
regular intervals in accordance with the infor-
mation supplied by the manufacturer.
•
Take precautions to prevent anything which
would weaken or damage the equipment, e.g.
from
a) striking or engraving,
b) modifi cations which are prohibited by the ma-
nufacturer,
c) guiding on templates made of hard material,
e.g. steel,
d) pushing across the fl oor,
e) using as a hammer,
f) any kinds of acts of violence.
5.1 Checking the trigger catch (Fig. 1)
Warning!
Remove the battery.
Check the trigger catch (6) each time before use.
The trigger catch must move freely without jam-
ming. The spring on the stapler head and trigger
catch must return the trigger catch to the released
initial position again. Never use the equipment if
the trigger catch is not working.
1. Take the rechargeable battery out of the
equipment.
2. Remove the staples/nails from the magazine
(Fig. 3/Item 4).
3. Check that the stapler head and the trigger
catch (6) can move up and down freely.
4. Push the rechargeable battery back into the
equipment.
5. Press the stapler head/trigger catch (6)
against the workpiece without pressing the
trigger (1). The equipment should not operate.
Never use the equipment if it operates without
the trigger (1) being pressed. Risk of injury!
6. Remove the equipment from the workpiece.
The stapler head and trigger catch (6) must
return to the released initial position. Press
the trigger (1). The equipment should not ope-
rate. Do not use the equipment if it operates.
Risk of injury!
Anl_TE_CN_18_Li_SPK13.indb 17 Anl_TE_CN_18_Li_SPK13.indb 17
GB
7. Press the stapler head and trigger catch (6)
against the workpiece and press the trigger
(1); the equipment will operate.
5.2 Loading staples and nails (Fig. 2-6/Item 4)
Warning!
Remove the battery.
•
When you fill the magazine (4), make sure
that you hold the equipment in such a way
that the muzzle is pointed neither at yourself
nor at anyone else.
•
To fill the magazine, press the magazine re-
lease (2) and slide back the magazine cover
(3) as far as it will go (see Fig. 3).
•
Staples:
Insert the staples against the top edge and
push them towards the front as shown in Fig.
4.
•
Nails:
Insert the nails with the pointed end down-
wards against the bottom edge and push
them towards the front as shown in Fig. 5.

Important!

It must be possible to move the magazine slide
without applying much force. Watch out for jam-
med staples and nails.
5.3 Charging the Li battery pack (Fig. 7-8)
1. Remove the battery pack (a) from the handle,
pressing the pushlock button (b) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(c) into the socket outlet. The green LED will
then begin to blink.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger
•
and the battery pack
to our customer service center.
- 17 -
09.09.2021 12:06:05 09.09.2021 12:06:05