Table des Matières
Publicité
Anleitung LE-HP 1500-2_SPK7
GB
Before starting operation, be sure to read the
operating and safety instructions!
Proper use
The hot air gun is designed for heating shrink-down
plastic tubing, for stripping paints and for welding and
shaping plastics.
Attention:
Fire hazard during use!
1 nozzle
2 2 level ON/OFF switch
3 suspension shackle
4 power cable
Technical data:
Nominal voltage:
230 V ~ 50 Hz
Power rating:
Temperature:
375°C / level 1
500°C / level 2
Air rate:
400 l / level 1
550 l / level 2
Sound pressure level LPA :
Sound power level LWA :
Vibration
a
–
w
Weigth
Safety Instructions:
Before plugging in the power supply cord, be sure
that the ON/OFF switch is in the central position.
The nozzle reaches temperatures of up to
600°C. Fire hazard! Wear protective gloves
and eye wear. The nozzle should not be tou-
ched during operation.
Allow the hot air pistol to completely cool before
putting away.
Never expose the unit to rain or moisture. Store
the unit in a dry place.
Do not leave the unit unattended. Keep out of
reach of children.
Never direct the air flow at people or animals.
Do not use the unit to dry clothing or hair. Do
not use the hot air blower as a hair dryer.
Do not use the unit near easily flammable or
explosive substances or gasses.
Never block the hot air flow by plugging or cover-
ing the air flow exit.
Use only original accessory and replacement
10
28.06.2006
10:13 Uhr
parts from the manufacturer.
Do not wear loose clothing or jewelry. Wear slip-
resistant shoes and wear a hair net for long hair.
During operation maintain a secure footing.
Never use the unit in wet surroundings or in areas
with high humidity (bathroom, sauna, etc.).
Check your work area for easily flammable sub-
stances and materials before using the hot air
pistol.
Never carry the hot air pistol by the power supply
cord.
Only use extension cords with a minimum cross-
section area of 1,5 mm
2
.
Repairs (for example power supply cord replace-
ment) should be performed only by a qualified
electrician.
Do not use chemical paint removers or solvents
at the same time as the hot air pistol.
Clean the nozzle when soiled.
1500 watt
Be sure that the openings for air entry and exit
are always clean and free of dirt.
Hazardous or poisonous gasses can be freed
when removing paint. Be sure to provide adequa-
te ventilation while working indoors.
Never point the hot air directly at windows or
other glass surfaces.
72 dB(A)
Start of operation:
82 dB(A)
Be sure that the power supply voltage matches that
< 2,5 m/s
2
printed on the model name-plate.
Choose the desired temperature and air quantity with
0,7 kg
the ON/OFF switch (2). The hot air pistol reaches the
working temperature within one minute.
Switch position 1:
1st level - 375 °C / 400 l liters per minute.
Center position:
The tool is switched off.
Switch position 2:
2nd level - 500 °C / 550 l liters per minute
Possible uses for the hot air pistol:
1. Removal of paint and lacquer. Attention!
Hazardous or poisonous gasses may be pro-
duced while removing paint or lacquer. Be
sure to provide adequate ventilation.
2. Removal of stickers and decorations.
3. Loosening of rusted or tightly fastened nuts and
metal screws.
4. Thawing of frozen pipes, door locks, etc.
Attention: no not attempt to thaw plastic or syn-
thetic pipes.
Seite 10
Publicité
Table des Matières
