Die Heads And Dies; Maintenance Instructions; Lubrication; Oil System Maintenance - RIDGID 535 Manuel

535 Manual Pipe and Bolt Threading Machine

Die Heads and Dies

Model
811A NPT
815A NPT
842 NPT
816 NPT
817 NPT
811A BSPT
815A BSPT
531 Bolt
532 Bolt
Universal Pipe Die
(Catalog Numbers)
H.S. R.H.
H.S. L.H.
H.S. for S.S. R.H.
H.S. for C.I. R.H.
H.S. for PVC R.H.
H.S. for Coated R.H.
Universal Pipe Die
(Catalog Numbers)
H.S. R.H.
H.S. L.H.
H.S. for S.S. R.H.
H.S. for S.S. L.H.
H.S. for PVC R.H.
H.S. for Coated R.H.
Note: BSPT and BSPP Dies require a British Model Die Head
Note: L.H. operation of the 1822-I requires special set up
Note: High Speed Dies are recommended for threading 1" - 2" pipe at 45 RPM
Universal Bolt Dies for 811A, 815A, 816 and 817 Die Heads
Over 90 sets available from
Right Hand only in UNC, UNF and BSW thread forms.
NOTE! See Ridge Tool catalog for complete list of pipe
supports, thread cutting oil and dies.

Maintenance Instructions

WARNING
Make sure machine is unplugged from power
source before performing maintenance or mak-
ing any adjustment.

Lubrication

Proper lubrication is essential to trouble-free operation
and long life of Power Drive.
1. Remove four (4) cover mounting screws and remove
the cover.
2. Use grease gun to apply grease to the shaft bearing
grease fittings every 2 to 6 months, depending upon
frequency of machine use.
12
Pipe Bolt
Capacity Capacity
" - 2" " - 2"
1 / 1 /
8 4
" - 2" " - 2"
1 / 1 /
8 4
" - 2"
1 / —
4
" - " " - 2"
1 / 3 / 1 /
8 4 4
" - 2"
1" - 2" 1 /
4
" - 2" " - 2"
1 / 1 /
8 4
" - 2" " - 2"
1 / 1 /
8 4
" - 1"
— 1 /
4
" - 2"
— 1 1 /
8
NPT
" " - "
1 / 1 / 3 /
8 4 8
47755 47760
— 47810
47775 47780
— —
— —
— —
BSPT
" " - "
1 / 1 / 3 /
8 4 8
66750 66755
— 66840
66770 66775
— 66855
— —
— —
" to 2", Alloy or High Speed.
/
1
4
Dies
Universal
Universal
Universal
Universal
Universal
Universal
Universal
500B
500B
" - "
1 / 3 / 1" - 2" 1 /
2 4
47765 47770 47845
47815 47820 —
47785 47790 —
— 70740 —
70745 70750 —
— 31822 —
" - "
1 / 3 / 1" - 2" 1 /
2 4 8
66760 66765 66795
66845 66850 —
66780 66785 66815
66860 66865 —
70755 70760 —
— 31837 —
500B Bolt Dies for 531 and 532 Die Heads
Over 200 sets for the 531 Bolt Die Head
Over 150 sets for the 532 Bolt Die Head
Mono Dies for Mono (A Series) Die Heads
3. Apply moderate coat of lubricating grease on large
gear each time bearings are lubricated.
WARNING
with cover off. Always replace cover immediately after
lubricating machine.

Oil System Maintenance

To help assure proper operation of threading machine,
keep oil system clean, as follows:
1. Replace thread cutting oil when it becomes dirty or
contaminated. To drain the oil, position a container
under drain plug and remove plug.
2. Keep oil filter screen clean to assure proper flow or
clean oil to work. Oil filter screen is located in the bot-
tom of oil reservoir. To clean filter screen, loosen
the screw that secures filter to base and pull filter from
oil line. Clean filter screen in solvent and blow out with
Opening Operation
Quick
Self
Quick
TAP
TAP
Quick
Self
Quick R.H./L.H.
Quick R.H./L.H.
NPSM
" " - " " - "
1 / 3 / 1 / 3 /
8 4 8 2 4
47850 47855
— —
— —
— —
— —
— —
BSPP
" " - " " - "
1 / 3 / 1 / 3 /
4 8 2 4
66800 66805
— 66870
66820 66825
— —
— 70765
— —
Do not operate the threading machine
R.H.
R.H.
L.H.
R.H.
R.H.
R.H.
R.H.
1" - 2"
47860
70775
—
—
—
—
1" - 2"
66810
66875
66830
—
70770
—