Woods BW15.70E Manuel De L'utilisateur page 19

7.
Remove snap ring (10) and shim (13) from front of housing (2).
8.
Remove input bearing (7) by using a punch and hammer from outside of
housing.
9.
Support housing in vise in a horizontal position.
10.
The castle nut (15), cotter pin (25), and hub are already removed with the
stump jumper/crossbar. Remove the protective seal (8), and oil seal (18).
11.
Remove cotter pin (9), castle nut (14), and shim (17) from output shaft
(4).
12.
Remove output shaft (4) by using a punch and hammer and tap on top to
drive down. Remove gear (5) and shim (16) from inside housing.
13.
Remove bottom bearing (26) by using a punch and hammer from the top,
outside the housing.
14.
Support housing upside down (top cover surface) and remove bottom
bearing (6) by using a punch and hammer from the bottom side of the
housing.
15.
Inspect gears for broken teeth and wear. Some wear is normal and will
show on loaded side. Forged gear surfaces are rough when new. Check
that wear pattern is smooth.
16.
Inspect vertical and horizontal shafts for grooves, nicks, or bumps in the
areas where the seals seat. Resurface any damage with emery cloth.
17.
Inspect housing and caps for cracks or other damage.
Assembly (Figure 13)
1.
Clean housing, paying specific attention to areas where gaskets will be
installed.
2.
Wash housing and all components thoroughly. Select a clean area for
gearbox assembly. Replace all seals, bearings, and gaskets. All parts
must be clean and lightly oiled before reassembling.
3.
Insert both output bearings (6) in the housing, using a round tube of the
correct diameter and a hand press.
4.
Slide output shaft (4) through both bearings (6) until it rests against top
bearing (6).
5.
Slide shim (16) over output shaft (4).
6.
Press gear (5) onto output shaft (4) and secure with shim (17), castle nut
(14), and cotter pin (9).
7.
Apply grease to lower seal lips (18) and press seal (18) over output shaft
(4), using a tube of the correct diameter. Be sure not to damage the seal
lip.
1. Crown gear
2. Gearbox housing
3. Input shaft
4. Output shaft
5. Gear pinion
6. Bearing
7. Input bearing
8. Protective seal
9. Cotter pin
10. Snap ring
11. Snap ring
12. Shim, 45.3 x 2.5
13. Shim, 70.3 x 84.7
14. Nut
15. Castle nut
16. Shim, 50.3 x 70.3
17. Shim
18. Oil seal (Vertical Shaft)
19. Oil seal (Horizontal Shaft)
20. Cap
MAN1258 (3/26/2018)
22. Top cover
23.Cap screw 8mm x 16
(8.8)
24. Dip Stick
25. Cotter Pin
26. Washer
Figure 13
8.
Press in housing so that seal is recessed. Press protective seal (8) until
seated flush with housing. Verify that the seal (8) is seated correctly.
9.
Press bearing (7) into the housing, using a round tube of the correct
diameter and a hand press. Secure with shim (13) and snap ring (10).
10.
Secure snap ring (11) on input shaft (3) if not already secure.
11.
Place gear (1) through top of housing and align gear (1) and gear (5) so
that gear teeth are a match.
12.
While holding gear (1) in place, slide input shaft (3) through gear (1) and
bearing (7). Align splines on shaft (3) and gear (1).
13.
Slide shim (12) over input shaft (3) and press bearing (7) onto input shaft
(3), using a round tube of the correct diameter and a hand press.
14.
Slide shim (13) over input shaft (3) and secure with snap ring (10).
15.
Check input shaft end float by moving the input shaft (3) by hand. If end
float is higher than .30 mm (0.012"), insert shim between input shaft (3)
and rear bearing (7). Repeat until end float is less than .30 mm (0.012").
Check rotational torque by hand. The torque should be less than .25 Nm
(2.2 lbs-inch).
16.
Check that the gear backlash is between .15 Nm (0.006") and .41 Nm
(0.016"). You should not have to adjust the backlash.
17.
Press in input oil seal (19), using tube of correct diameter. Be careful not
to damage seal lip.
18.
Press oil cap (20) on to cover the rear of housing, using a tube of the
correct diameter.
19.
Place top cover (22) on top of housing and secure with six cap screw
(23).
20.
Check gearbox housing for leaks by plugging all holes except one. Apply
27.6 kPa (4 psi) compressed air and immerse the gearbox in water to
verify that there are no leaks.
21.
Remove gearbox from water and dry off with compressed air. Add SAE
80W or 90W EP oil to proper level. Tighten all plugs.
Reinstallation
NOTE: Gearbox is heavy: do not attempt to move without mechanical assis-
tance.
1.
Set gearbox on cutter and fasten with bolts and nuts. Torque bolts to 407
Nm (300 lbs-ft).
2.
Attach crossbar (Crossbar Installation, page 22).
. Gearbox
Dealer Service 19