Specific Safety Instructions - NUTOOL NCHD18-2 Traduction Des Instructions Originales

GB

SPECIFIC SAFETY INSTRUCTIONS

Be aware of the high torque reaction when drilling especially
when drilling masonry.
DO NOT try to change any of the selector switches while the
motor is running. Doing so could damage the machine.
DO NOT attempt to modify the machine or its accessories in
any way.
DO NOT force the machine, let the machine do the work. This
will reduce the wear on the machine and cutter and increase its
efficiency and operating life.
Do not use this product with any attachment designed for mixing
mortar, concrete, or plaster. Or for any other type of mixing
operation.
ADDITIONAL SAFETY RULES FOR DRILLS
- If possible, always use clamps or a vice to hold your work.
- Always switch off before you put the drill down.
- When using the drill, use safety equipment including safety
glasses or shield, ear defenders, and protective clothing
including safety gloves. Wear a dust mask if the drilling
operation creates dust.
-
ADDITIONAL SAFETY RULES CHARGERS
1. Before using the charger, read all the instructions and
cautionary markings on the charger and battery pack as well
as the instructions on using the battery pack.
2. Only charge your batteries indoors as the charger is
designed for indoor use only.
3. DANGER. If the battery pack is cracked or damaged in any
other way, do not insert it in the charger. There is a danger
of electric shock or electrocution.
4. WARNING. Do not allow any liquid to come into contact with
the charger. There is a danger of electric shock.
5. The charger and battery packs supplied with it are
specifically designed to work together. Do not attempt to
charge the battery pack with any other charger than the one
supplied.
6. Do not pull on the power cord to disconnect it from the
mains supply socket.
7. Do not use the charger if it has been subjected to a heavy
knock, dropped or otherwise damaged in any way. Take
the charger to an authorised service centre for a check or
repair.
8. Do not disassemble the charger. Take it to an authorised
service centre when service or repair is required. Incorrect
re-assembly may result in the risk of fire, electric shock or
electrocution.
9. To reduce the risk of an electric shock, unplug the charger
from the power supply before attempting to clean it.
Removing the battery alone does not reduce the risk.
ADDITIONAL SAFETY RULES FOR THE BATTERY
PACK
1. The battery pack for this tool has been shipped in a low
charge condition. You should charge the battery pack fully
before use.
2. Do not incinerate the battery pack even if it is seriously
damaged or can no longer hold a charge. The battery pack
can explode in a fire.
3. A small leakage of liquid from the battery pack may occur
under extreme usage or temperature conditions. This
does not necessarily indicate a failure of the battery pack.
However, if the outer seal is broken and this leakage comes
into contact with your skin wash the affected area quickly
with soap and water. If the leakage gets in your eyes flush
your eyes with clean water for a minimum of 10 minutes and
seek immediate medical attention. Inform the medical staff
that the liquid is a 25-35% solution of potassium hydroxide.
4. Never attempt to open the battery pack for any reason. If the
plastic housing of the battery pack breaks open or cracks,
immediately discontinue its use and do not recharge it.
5. Do not store or carry a spare battery pack in a pocket or
toolbox or any other place where it may come into contact
with metal objects. The battery pack may be short-circuited
causing damage to the battery pack, burns or a fire.
BATTERY CHARGING INFORMATION
Charging rates for NiCad
Nicad battery charging rates are determined by the time taken
to fully charge the battery and are determined by the charge
current. The three most commonly used charging rates are
typically:
Fast charge.
Slow charge.
Trickle charge.
Fast charge batteries
The charging rates for fast charge batteries can vary between
30 minutes and 90 minutes. The charging rate for the battery
supplied with a cordless power tool is stated in the product
manual.
Slow charge battery.
The charging rates for slow charge batteries are between 3
Hours and 5 Hours.
Trickle charge batteries.
The charging rates for trickle charge batteries are between 7
Hours and 9 Hours.
IMPORTANT NOTICE
NiCad battery charging information.
ALWAYS FULLY DISCHARGE A NiCad BATTERY BEFORE
CHARGING AND NEVER EXCEED THE CHARGING RATE
TIME, EXCEPT WHEN "CONDITIONING" A NEW BATTERY
Charging procedure
When charging a new NiCad battery it should be fully discharged
followed by a full charge for the charging rate for the battery as
stated in the product manual plus 30 minutes. This should then
be followed by a full discharge and a further full charge for the
charging rate for the battery as stated in the product manual
plus 30 minutes. This procedure will condition the battery and
equalise the cell voltages. Following this procedure will ensure
the optimum operation of the battery.
When repeatedly using the charger to charge a number of
batteries always allow the charger to cool down before charging
another battery. It is recommended that the cooling down period
14