Asist AE9BS06DN Mode D'emploi page 38

engage in the grinding station mechanism.
REPLACING FOCUS ATTACHMENTS
Press the lever to release the attachment. Simultane-
ously pull the attachment upwards from the guide rail.
SWITCHING ON
Press button 3 to position „I" to start the device.
OFF
Press button 3 to position „O" to switch off the device.
The device is not intended for continuous operation
- after 30 minutes of use it must be switched off and
allowed to cool down completely.
DRILL SHARPENING
With this grinding station, drills with a diameter of
3-13 mm can be sharpened.
PREPARATION
1) Attach the drill bit attachment to the side where the
grinding wheel is located.
2) Remove the drill holder from the drill sharpening
attachment and insert the drill bit into it. Fix the drill in
the holder with the nut for fixing the drill so that it fits
firmly, but can still move in the holder.
3) Insert the holder with the drill bit inserted into the
setting compartment.
It is essential that the holder fits into the rails of the
adjusting compartment.
4) Slide the drill forward and rotate it so that it rema-
ins in the V-shaped groove. The tip of the drill should
touch the metal stop. The blades must rest on the
metal sides of the groove.
5) Tighten the nut to secure the drill - fix the drill in
the holder,
6) Remove the drill holder from the adjustment
compartment and insert it back into the drill bit at-
tachment. Make sure that the holder fits into the rails
in the attachment.
7) Check that the drill blades touch the grinding whe-
el. If not, repeat the drill alignment described above.
8) The drill can now be sharpened.
FOCUS
1) Switch on the sanding station and move the upper
part of the drill sharpening attachment to the right and
left to sharpen both blades.
2) Switch off the sanding station, remove the drill
holder from the bit, turn it and insert it back into the bit
so that the opposite side of the cutting edges can be
sharpened.
3) Repeat the focusing procedure for the same time.
4) Remove the drill holder and check that the cuts
of both drill grooves are equally sharp. They should
meet in the middle.
5) Repeat sharpening if any deviations need to be
corrected.
SHARPENING OF CHISELS AND PLANING KNIVES
With this grinding station, chisels and planing knives
with a width of 6-51 mm can be sharpened.
Focus angle (15-50 °) can be adjusted by adjusting
the angle.
Loosen the angle adjustment handle, tilt the support
plate to the desired angle and tighten the handle.
PREPARATION
1) Attach the drill bit attachment to the side where the
grinding wheel is located.
2) Place the blade on the support plate so that the
side of the chisel or planing knife rests on the end of
the edge of the plate.
The blade is held in place by magnets. To sharpen
narrow chisels, attach the spacer to the edge of the
support plate.
3) Check that the plate angle matches the existing
blade angle. Only in this way can the optimum clam-
ping angle of the blade be ensured.
4) Make sure that the cutting edge touches the grin-
ding wheel and that the protective cover is fitted.
FOCUS
1) Switch on the sanding station and move the sup-
port plate forwards and backwards while holding the
tool in position. Use constant pressure and focus on
steady and even movements.
2) While sharpening, slide the blade down toward the
grinding wheel while maintaining a constant, gentle
pressure.
3) Remove the workpiece and check that the angle
and the cutting edge are sharp and even along their
entire length.
4) Remove any unevenness by continuing to focus.
SHARPENING OF KNIVES AND SCISSORS
With this universal grinding station, all knives and
scissors with straight blades with a smooth surface
can be sharpened. Blades with corrugated and spe-
cial cutting edges will be damaged by grinding.
1) Attach the attachment for sharpening knives and
scissors to the side where the grinding wheel is
located.
KNIFE SHARPENING
1) Switch on the sanding station.
2) Insert the knife into one of the notches on the knife
and scissor attachment so that the cutting edge faces
the grinding wheel.
3) Slide the blade along the grinding wheel slowly by
pulling it towards you. Maintain only a slight pressure
so that the contact with the grinding wheel is maintai-
ned up to the tip of the blade.
4) Turn the knife and insert it into the opposite notch
on the attachment. Repeat step 3.
5) Repeat sharpening alternately until the cutting
edge is sharp and clean.
SCISSOR SHARPENING
1) Switch on the sanding station.
2) Open the scissors completely.
3) Place one of the scissor blades in the notch for
sharpening the scissors (below on the attachment).
Hold the scissors fully open and hold the other blade
on the right side.
4) Pull the blade along the grinding wheel from the
screw to the tip under constant and gentle pressure.
38