Table des Matières
Publicité
I. BEFORE THE FIRST USE
Carefully remove the unit and its accessories from the packaging. Dispose of
all packaging materials and promotional stickers.
Keep all warning labels and the serial number identification label located on the
housing. The absence of the serial number will deprive you of your warranty benefits!
Unwind the power cord. Wipe the housing with a damp cloth. Wash removable
parts with warm soapy water and dry thoroughly before connecting the appliance
to an electrical outlet.
After transporting or storing at low temperatures allow the appliance to stay
at room temperature for at least 2 hours before using.
II. OPERATING THE HAND BLENDER
General Guidelines
•
Do not fill the food vessel more than 2/3 full to prevent splattering.
•
When using the whisk or blending attachment place the attachment into
food first and then press the Power of Turbo mode button. Always release
the button before removing the hand blender from the vessel.
•
Start operating at a low speed and gradually increase it by rotating the
speed control knob on the handle. The control knob has a dial: select an
optimal operating speed setting by rotating the speed control knob.
•
To process at a maximum speed (when blending tough ingredients or for
the final whipping stage) press and hold down the Turbo mode button.
Do not immerse the blender above the joint between the motor unit and the
attachment.
•
Defrost, de-bone, clean, and cut meat into 1-1.5 cm cubes before processing.
•
Remove the pits and cut fruits and berries into pieces before processing.
•
Do not use the hand blender to mash potatoes.
•
Remove the pot from the stove top and let cool down before processing hot
foods. Do not process any food or liquid at a temperature higher than 80°C.
Start processing at a low speed to avoid splatter. Do not use the blender to
process coffee beans, ice cubes, sugar, grain, beans, and other tough foods.
Do not use the chopper bowl for blending or whisking. The central pin at the
bottom of the chopper bowl can damage the attachment. Use the beaker
provided with the appliance.
8
To operate the whisk
1. Fill the beaker or a similar vessel with food.
2. Insert the whisk attachment to gear box until it clicks into place.
3. Press and hold both attachment fixation buttons simultaneously. Connect
the whisk attachment to the motor unit and turn counterclockwise until
it clicks into place.
4. Plug in the appliance. Turn the speed control knob counterclockwise to
setting 1 (minimum speed).
5. Hold the vessel steady and place the whisk attachment in food. Press and
hold down the Power button. Turn the speed control knob clockwise to
increase the speed if necessary (from 1 to 5). To whisk at a maximum
speed press and hold down the Turbo mode button.
6. Whisk foods using clockwise circular motion.
7. After use unplug the appliance. Press and hold the attachment fixation
buttons simultaneously and gently disconnect the whisk attachment.
8. Clean the appliance in accordance with the table A1.
To operate the chopper
1. Place a large or a small bowl on a flat stable horizontal surface.
2. Fit the S-shaped blade on a central pin at the bottom of the chopper
bowl. Note: the blade is very sharp, handle with caution! Always hold the
blade by the plastic collar.
3. Fill the bowl with food. Do not fill above the maximum fill mark. Follow
the procedures outlined in "General Guidelines" section.
4. Fit the lid onto the bowl, aligning the crosspiece of the plastic collar with
the corresponding notches in the center of the lid. Align the projections
on the sides of the lid with the corresponding notches on the bowl edges.
Gently press the lid down and rotate clockwise until it clicks into place.
5. Press and hold both fixation buttons simultaneously and connect the
motor unit with the fixation hole on the bowl lid.
6. Plug in the appliance. Select the speed setting: harder foods require
higher chopping speed.
7. Turn the speed control knob clockwise to increase the speed. Steadily
holding the vessel with one hand press and hold down the Power or Turbo
mode button. Use Turbo mode for meat and other tough foods.
8. After use unplug the appliance. Press and hold both fixation buttons si-
multaneously and disconnect the motor unit. If you used the large bowl,
press the button on the bowl handle and turn the lid simultaneously
counterclockwise to remove.
9. Remove the S-shaped blade holding it by the plastic collar.
10. Clean the appliance in accordance with the table A1.
Publicité
Table des Matières
