Layout And Items Supplied - EINHELL GC-EL 3024 E Instructions D'origine

•
Always keep the ventilation opening clean.
•
Never direct the vacuum/blow hole at persons
or animals.
•
The machine may only be used at reasonable
times of the day, i.e. not in the early morning
or late evening when it will be a nuisance to
other people. Permitted times of use specified
by local authorities must be observed.
•
The machine must be run at the lowest pos-
sible motor speed required to carry out the
work.
•
Remove all foreign objects with a rake and
brush before starting any blowing work.
•
Where conditions are dusty, dampen the sur-
face a little or use a sprinkler attachment.
•
Use the full-length blower nozzle extension
so that the air current can work near to the
ground.
•
Watch out for children, pets, open windows
etc. and blow the foreign objects safely away
from them.
Maintenance and storage
•
Check that all nuts, bolts and screws are
securely tightened in order to be sure that the
machine is in a safe working condition.
•
Frequently check the debris bag for signs of
wear and deformation.
•
Use only genuine accessories and spare
parts.
•
For your own safety, replace worn or dama-
ged parts without delay.
•
Electric tools should be kept in a dry place
when not in use.
•
If the mains cable for this device is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained person-
nel to avoid danger.
The tool can be plugged into any socket-outlet
(with 230 V AC) that is equipped with a 10A fuse
or higher. The socket-outlet has to be safeguar-
ded by an earth-leakage circuit breaker (e.l.c.b.).
The operating current must not exceed 30 mA.
Explanation of the warning signs on the
equipment (see Fig. 10)
1. Read the directions for use before operating
the tool.
2. Do not use the tool in rain or snow. Do not ex-
pose the tool to wet conditions.
3. Keep all other persons away from the danger
zone.
4. Wear goggles and ear muff s.
Anl_GC_EL_3024_E_SPK13.indb 16 Anl_GC_EL_3024_E_SPK13.indb 16
GB
5. Switch off the tool and pull out the power plug
before carrying out any cleaning or mainte-
nance work.
6. Rotating parts. Keep your hands and feet
away from all openings.

2. Layout and items supplied

2.1 Layout (Fig. 1/2)
1. Front suction tube
2. Rear suction tube
3. Additional handle
4. Harness
5. On/Off switch
6. Power cable
7. Debris bag
8. Selector switch for blower/vac
9. Castors
10. Speed controller
11. Wheel support
12. Long screw (1x)
13. Short screw (3x)
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
•
Original operating instructions
- 16 -
18.01.2021 13:27:51 18.01.2021 13:27:51