Electrical Installation; Technical Data - Grohe Blue Chilled 40 693 Manuel D'utilisation

GB GB
Application
®
The GROHE Blue Chilled fitting with integrated cooler is
designed for use in the private, non-commercial sector.
The filter head is fitted with a type-tested non-return valve.
The cooler works with environmentally-friendly refrigerant.
Safety notes
This device is not intended for use by persons
(including children) with physical, sensory or mental
impairments or a lack of experience or knowledge
in using devices of this type.
Children must be supervised to ensure that they
do not play with the device.
Prevent danger resulting from damaged power
supply cables. In the case of damage, the mains
cable must be replaced by the manufacturer or his
customer service department, or an equally qualified
person.
The mains plug provided (type EF plug) is only
suitable for use with Schuko (CEE 7/4) sockets.
• During cleaning, do not spray the cooler or the plug directly
or indirectly with water.
• The cooler must be connected to a permanent power
supply.
• At the installation location, the cooler and filter system must
be protected from mechanical damage, heat and direct
sunlight.
Do not install near heat sources or an open fire.
• The cooler must be placed in an upright position.
• The cooler must not be opened.
• Installation of the fitting and cooler with filter cartridge is
only permitted in frost-free rooms.
• The cooler is only suitable for indoor use.
• Adequate ventilation must be ensured. If necessary, provide
ventilation grilles in the cover of the lower cabinet.
• Use only genuine replacement parts and accessories.
The use of other parts will result in voiding of the warranty
and the CE identification, and could lead to injuries.

Technical data

Cooler electrical data:
• Connection: Wall socket with earth wire, protected
• Voltage supply:
• Max. power consumption:
• Type of protection:
• Relative air humidity:
• Refrigerant:
• Safety shut-off of pump:
Sanitary data:
• Cooler cooled water capacity:
• System operating pressure:
• Flow rate at 0.3 MPa flow pressure:
• Ambient temperature:
• Temperature
– Cooler water inlet:
– Cooled water temperature:
• Sound pressure level L
• Adjustable bypass, factory setting:
• Filter capacity at bypass setting 2
(Carbonate hardness 10 - 24 °KH):
• Water connection
– Cooler:
Electrical test data
• Software class:
• Contamination class:
• Rated surge voltage:
The test for electromagnetic compatibility (interference emission
test) was performed at the rated voltage and rated current.
Approval and conformity
This product conforms to the requirements of the
relevant EU guidelines.
The conformity declarations can be obtained from the following
address:
GROHE Deutschland Vertriebs GmbH
Zur Porta 9
D-32457 Porta Westfalica

Electrical installation

Electrical installation work must only be performed
by a qualified electrician. This work must be
carried out in accordance with the regulations
according to IEC 60364-7-701 (corresponding
to VDE 0100 Part 701) as well as all national and
local regulations.
Installation
Refer to the installation dimensions on fold-out page I.
Install cooler, see fold-out page I, Fig. [1].
When transporting or installing the cooler, cooling
fluid may have run into the lines. In order to ensure
that the cooling fluid has run back, the cooler may
only be switched on following a pause of 24 hours.
via a 10 A fuse
230 V AC / 50 Hz
Connect cooler, see fold-out page I, Figs. [2] to [4] and fold-
out page II, Fig. [5]
180 W
IP21
Open hot and cold water supply and check that
max. 75%
connections are watertight.
0.065 kg - R134a
Connect plug-in connection between fitting and cooler,
approx. 4:30 min
see fold-out page II, Fig. [6].
Establish voltage supply via mains plug, see Fig. [7].
The display illuminates and the remaining filter capacity is
displayed in percent.
max. 0.6 MPa
approx. 2 l/min
4 – 32 °C
max. 20 °C
approx. 5 – 10 °C
A: 50 ± 4 dB
p
max. 750 liters
corresponds to max. 12 months
hot - red
cold - blue
2,500 V
1.4 l
2
A
2
4