Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
3.2.2
Bonding and Grounding
1.
In addition to being properly grounded as
described below in Sec. 3.2.3, and in accordance
with the requirements of the National Electrical
Code (NEC), or in Canada the Canadian
Electrical Code (CEC), the pump motor must
be bonded to all metal parts of the swimming
pool, spa or hot tub structure and to all electrical
components and equipment associated with the
pool/spa water circulation system.
2.
The bonding must be accomplished by using a
solid copper conductor, No. 8 AWG or larger.
In Canada No. 6 AWG or larger must be used.
Bond the motor using the external bonding lug
provided on the motor frame.
RECOMMENDED MINIMUM WIRE SIZE FOR SHP PUMPS* (1-PHASE POWER)
Distance from Sub-Panel
Inverse - Time Circuit
Breaker or Branch
Pump Model
Class: CC, G, H, J, K,
208-
230VAC
SHPF.50 / SHPM.75
15A
SHPF.75 / SHPM1.0
15A
SHPF1.0 / SHPM1.5
15A
SHPF1.5 / SHPM2.0
15A
SHPF2.0 / SHPM2.5
15A
SHPF3.0
20A
SHPF5.0
25A
SHPF1.0-2 **
15A
SHPF1.5-2 **
15A
SHPF2.0-2 **
15A
SHPM1.5-2 **
15A
SHPM2.0-2 **
15A
SHPM2.5-2 **
15A
*Assumes three (3) copper conductors in a buried conduit and 3% maximum voltage loss in branch circuit. All National Electrical Code
followed. Table shows minimum wire size and branch fuse recommendations for a typical installation per NEC.
**Two-speed pumps are not rated for use with 208 VAC.
RECOMMENDED MINIMUM WIRE SIZE FOR SHP PUMPS* (3-PHASE POWER)
Distance from Sub-Panel
Inverse - Time Circuit
Breaker or Branch
Fuse AMPs
Pump Model
Class: CC, G, H, J, K,
RK, or T
460VAC
SHPF1.0-3PH
15A
SHPF1.5-3PH
15A
SHPF2.0-3PH
15A
SHPF3.0-3PH
15A
SHPF5.0-3PH
15A
*Assumes four (4) copper conductors in a buried conduit and 3% maximum voltage loss in branch circuit. All National Electrical Code
followed. Table shows minimum wire size and branch fuse recommendations for a typical installation per NEC.
Table 2.
Recommended Minimum Wire Size
Jandy
Stealth
®
0-50 Feet
Fuse AMPs
Voltage
RK, or T
115VAC
208-230VAC 115 VAC 208-230VAC 115 VAC
15A
14
15A
14
20A
12
N/A
12
N/A
12
N/A
10
N/A
10
N/A
12
N/A
12
N/A
12
N/A
12
N/A
12
N/A
12
0-50 Feet
Voltage
115VAC
460VAC
208-230VAC
15A
14
15A
12
15A
12
15A
12
20A
10
|
Pumps
Operation Manual
™
National Electrical Code® (NEC®) requires bonding
of the Pool Water. Where none of the bonded pool
equipment, structures, or parts are in direct connection
with the pool water; the pool water shall be in
direct contact with an approved corrosion-resistant
conductive surface that exposes not less than 5800
mm² (9 in²) of the surface area to the pool water at all
times. The conductive surface shall be located where
it is not exposed to physical damage or dislodgement
during usual pool activities, and it shall be bonded in
accordance with the bonding requirements of NEC
Article 680. Refer to locally enforced codes for any
additional bonding requirements.
50-100 Feet
Voltage
12
12
8
12
12
8
10
10
8
N/A
10
N/A
N/A
8
N/A
N/A
8
N/A
N/A
6
N/A
N/A
10
N/A
N/A
10
N/A
N/A
8
N/A
N/A
10
N/A
N/A
10
N/A
N/A
8
N/A
50-100 Feet
Voltage
460VAC
208-230VAC
12
12
12
12
10
10
12
10
10
12
8
8
10
6
6
ENGLISH
100-150 Feet
150-200 Feet
Voltage
208-230VAC 115 VAC
208-230VAC
10
6
8
10
6
8
8
6
6
8
N/A
6
6
N/A
6
6
N/A
4
4
N/A
4
8
N/A
6
8
N/A
6
6
N/A
6
8
N/A
6
8
N/A
6
6
N/A
6
(NEC
) and local codes must be
®
®
100-150 Feet
150-200 Feet
Voltage
460VAC
208-230VAC
460VAC
10
10
8
8
8
6
8
8
6
6
6
6
4
4
4
(NEC
) and local codes must be
®
®
Page 9
Voltage
115 VAC
6
6
4
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Voltage
208-230VAC
8
6
6
6
4
Publicité
Chapitres
Table des Matières
Dépannage
