Turning Off And Releasing From The Wheelchair; Klick Electric Tetra Version Operation; User Interface; Turning On And Setting Up The Device - Klaxon KLICK ELECTRIC Manuel D'emploi

The brake lever, the accelerator control, the reverse button and the display can be installed either on the left or on the right side
of the handlebar according to the user's preference.
For installation and positioning of controls (display, accelerator control, reverse button, brake lever),
DANGER
contact an authorised KLAXON service centre.
Before using reverse to move the device, make sure that there are no persons, obstacles, stairs,
DANGER
slopes behind the wheelchair.
At each restart pay maximum attention, before accelerating, to check if forward or reverse
DANGER operation is currently selected, especially when close to obstacles, drop-offs and any other kind of
danger.
If obstacles, drop-offs and dangers are too close to be safe, turn off the KLICK device and manually
DANGER
move the wheelchair to a safe place.

11.4 TURNING OFF AND RELEASING FROM THE WHEELCHAIR

To perform the operation properly, carefully follow the following instructions.
•
Stop the wheelchair on a flat surface.
•
Apply the brake on the wheelchair.
•
Turn off the display by pressing and holding the "
•
Push the handlebar forward with one hand grasping it in the middle and simultaneously press the release button on the
CONNECTOR with the other hand. This frees the lower pin of the KLICK coupling (Figure 34).
•
Reduce forward pressure on the handlebar while holding the release button on the CONNECTOR, thus lowering the
wheelchair so that its front wheels make contact with the pavement (Figure 35).
At this point the upper pin will already be pulled out the front hook of the CONNECTOR; release the wheelchair's brakes and push
yourself back to move away from the KLICK device (which in the meantime will remain upright thanks to its KICKSTAND - Figure
36).
Remove the CONNECTOR, pulling the lever located on its bottom (Figure 20).
During the KLICK release operation, pay attention to not endanger the top parts of your body
(fingers, hands, arms) as they could be affected by the sudden movement of the handlebar (or other
DANGER
parts of the device) if it is released too quickly. To avoid this danger, after pressing the release
button, gently release the handlebar by lowering the wheelchair gradually.

12. KLICK ELECTRIC TETRA VERSION OPERATION

12.1 USER INTERFACE

The device is equipped with a multifunction LCD display, used to switch the device on and off, select the maximum speed and
display several operating parameters (Figure 29).
•
The icon located top left (1) shows the current battery charge level.
•
The number (2) in the centre of the display shows the speed, in km/h.
•
The number (3) in the lower part of the display shows the distance travelled, in km.
•
The number (4) shows the desired maximum speed.
12.2 TURNING ON AND SETTING UP THE DEVICE (FIGURE 29).
A. Turning On and Selecting the Speed
•
M
Press and hold the "
•
+ -
Press the " " e " " buttons to select the desired maximum speed level (viewable in the left panel of the display, number (5)
in the legend); various speed levels can be selected, between 0 (motor disabled), 1 (minimum speed, 3 km/h), 2 (normal
speed, 6 km/h), 3 (medium speed, 10 km/h), 4 (high speed, 13 km/h) and 5 (maximum speed, 15 km/h).
B. Navigating the data
•
After turning on the display, the initial screen shows (in number 3) the total distance (ODO) the device has been used.
•
M
Press the " " button once to enter the second screen. It will show the partial distance (TRIP - number 3).
•
M
Pressing the " " button again for two times will display the time the device has been on, in minutes (TIME – number 3).
•
M
Pressing the " " button again for three times will display the maximum speed (ODO MAX – number 2); pressing the "
button again will display in the same screen the average speed (ODO AVG).
•
To reset trip data, hold down the "
C. Screen Backlighting
KLICK Electric User's Manual (ENG) - rev.6.1 of 15.06.2018
KLAXON Mobility Gmbh – ENG
M
" button for 5 seconds, until the display turns on.
M -
" and " " buttons together for 5 seconds.
" button for 5 seconds.
M
"
12