General Safety Information; Installing The Appliance; Changing Over Door Hinges - Atag KD8178AFUU/A01 Instructions De Montage

General safety information

Contents
1 General safety information................................... 14
2 Installing the appliance......................................... 14
3 Changing over door hinges.................................. 14
3.1 Demount door.......................................................... 15
3.2 Change freezer compartment door........................... 15
3.3 Changing bearing parts............................................ 15
3.4 Re-fit door................................................................ 15
4 Installation.............................................................. 15
4.1 Installing the appliance............................................. 17
4.2 Fitting the unit door .................................................. 18
5 Connecting the appliance..................................... 19
The manufacturer works constantly on the further development
of all the types and models. Therefore please understand that
we have to reserve the right to make design, equipment and
technical modifications.
To get to know all the benefits of your new appliance, please
read the information contained in these instructions carefully.
The instructions apply to several models. Differences may
occur. Text relating only to specific appliances is marked with
an asterisk (*).
Instructions for action are marked with a
action are marked with a
1 General safety information
DANGER identifies a situation involving direct
danger which, if not obviated, may
result in death or severe bodily
injury.
WARNING identifies a dangerous situation
which, if not obviated, may result in
death or severe bodily injury.
CAUTION identifies a dangerous situation
which, if not obviated, may result in
minor or medium bodily injury.
NOTICE identifies a dangerous situation
which, if not obviated, may result in
damage to property.
Note identifies useful information and tips.
It is important that the procedures and directions given in these
instructions are complied with in order that the appliance is
correctly installed and works properly. Read and grasp all the
information in these instructions before the appliance is
installed.

2 Installing the appliance

In the event that the appliance is damaged, contact the supplier
immediately before connecting to the mains.
The floor at the site must be flat and level.
Do not install the appliance in a location where it is exposed to
direct radiation of the sun, next to a cooker, heater and similar.
Do not install the appliance without assistance.
Standard EN 378 specifies that the room in which you install
your appliance must have a volume of 1 m
refrigerant used in the appliance. If the room in which the appli-
ance is installed is too small, a flammable gas-air mixture may
form in the event of a leakage in the refrigeration circuit. The
quantity of refrigerant used in your appliance is indicated on the
type plate on the inside of the appliance.
14
, the results of
.
per 8 g of R 600a
2
Fit the appliance in stable kitchen units only.
The following ventilation gaps must be observed:
The depth of the ventilation channel at the rear of the unit
q
must be at least 38 mm.
There must be a ventilation space of at least 200 cm
q
plinth and at the top of the unit.
Basically the principle applies: the larger the ventilation
q
space, the more energy-saving the appliance is in operation.
WARNING
Fire hazard due to dampness!
If live parts or the mains lead become damp this may cause
short circuits.
u The appliance is designed for use in enclosed areas. Do not
operate the appliance outdoors or in areas where it is
exposed to splash water or damp conditions.
WARNING
Fire hazard due to refrigerant!
The refrigerant R 600a is environmentally friendly but flam-
mable. Escaping refrigerant may ignite.
u Do not damage the piping of the refrigeration circuit.
WARNING
Fire hazard and danger of damage!
u Do not place appliances emitting heat e.g. microwaves,
toasters etc. on the appliance!
u Detach the connecting cable from the rear of the appliance,
removing the cable holder at the same time because other-
wise there will be vibratory noise!
After installation:
u Remove the protective film from the decorative trims.*
u Remove the protective film from the decorative trims and
drawer fronts.*
u Remove all transit supports.
u Unscrew the red transport
lock. Close the vacated
retaining hole using
stopper (60).
u Dispose of packaging material.
Note
u Clean the appliance .
If the appliance is installed in a very damp environment,
condensate may form on the outside of the appliance.
u Always see to good ventilation at the installation site.

3 Changing over door hinges

Ensure that the following tools are to hand:
q • Cordless screwdriver Torx® 15
Cordless screwdriver Torx® 20
•
• Cordless screwdriver Torx® 25
Slide the appliance 2/3 of the way into the recess.
Pull out the power plug.
Open the door.
2
the
in the