Floor Mounting; Wall Mounting - Toyotomi EPA-100EF Manuel D'utilisation

1. Function Introduction
(1) ON/OFF: Power on, inset the plug, the heater enters into standby mode. Press
under the previous mode, LED display show the set temperature. Power off, press
work and enter into standby mode, display show
(2) Power setting: When user uses the heater for the fi rst time, it works in default mode-high power. Press
into low power mode, the indicator light will on; press
will off, indicator light will on.
(3) Temperature setting: Under working mode, press
temperature range is 5°C-35°C. Press the key over 2s, the degree can set quickly. When fi nish setting, it confi rm
automatically, the dot stop fl ashing and off, the LED display shows setting temperature. Note: If under Anti-frost
mode, the temperature cannot be setting.
(4) Timer off setting: When the heater is working, press
press to set the hours, range is 0-24 hours. Press the
setting timer, the indicator light on. Display shows the set temperature.
(5) Anti-frost mode: Under working mode, press
cancelled and indicator light off.
(6) Child lock function: Press together for 3s, the display shows [ ] symbol, after 5s, display shows the previous
status, the keys cannot work. If press the keys, display is fl ashing [ ] symbol. Press
keys unlock.
(7) Memory function: If suddenly power off, after power on again, the heater will enter into previous working mode.
Installation the panel heater
Recommended Installation The convector shall be installed so that produced heat will mix
maximum volume of air. The convector should be attached in accordance with applicable
requirements. The switch and other mechanisms should be away from a person who takes bath
or shower. The device should not be exposed to water splashes. If the device is covered there is
a risk of overheating. It is strictly forbidden to cover or plug inlets and outlets (air grids) as it can
cause an accident or damage the device. DO NOT place the convector behind curtains, doors,
under wall opening or ventilation hole. Keep minimum distance required for installation on fl oor,
surface, near furniture, etc. (Figure 1).

Wall Mounting:

DO NOT fi t the castors to the base of the heater. Make sure
the heater is unplugged from the mains power and the wall
is suitable for mounting the panel heater and there are the
correct clearances. Make sure the panel heater is within 1
meter of a power socket.
Detach the mounting bracket from the rear of the heater by compressing the
2 bracket clips, pulling the clips out of the heater rear & removing the bracket
hooks from the heater.
and the heater start to work
again, the heater stop to
;
, enter into high power mode, the indicator light
to increase or decrease the temperature degree. The
, the timer indicator light will fl ash, the display shows timer,
over 2s, can set the hour quickly. After 5s fi nish
, the indicator light on. Press again, the anti-frost mode
together for 3s again, the
Figure 1
-3-
ENGLISH
Position the bracket on the wall in the desired position & drill holes for two mounting screws. Once the holes are drilled,
use two screws (appropriate for the type of wall) to fi x the bracket fi rmly in place. Check for strength.
Carefully place the heater (slightly tilted forward) onto the hooks at the bottom of the bracket & rotate back so the clips
fi x back into their original holes. Check that they are fi xed correctly. If possible, have a second person help to check for
alignment as the heater is attached. The heater is now ready to connect to the mains power.
, enter

Floor Mounting:

The device can be mounted on special legs enabling to move it in the room.
Support foots are attached as follows:
Turn the convector upside down;
Take one of support foots with rollers;
Place the plate of the support foot to the attaching point on the convector so that the dome-shaped part of the plate will
be tightly attached to the convector close to its rear panel the screw holes should match;
Tighten the support foots with the screws in parts kitting.
-4-
ENGLISH