Environmental Conditions; Warranty; Disposing The Equipment When No Longer Used; Safety Rules - CASTELLINI SKEMA 6 CART Instructions De Service

1.2.2. Environmental conditions

The equipment is to be installed in rooms that satisfy the following requirements:
• temperature between 10 and 40 °C.
• relative humidity between 30 and 75%.
• atmospheric pressure ranging from 700 to 1060 hPa.
• air pressure entering equipment ranging from 6 to 8 bar.
• water hardness entering equipment not over 60 mg/l.
• water pressure entering equipment ranging from 3 to 5 bar.
• water temperature entering equipment not higher than 25 °C.

1.2.3. Warranty

CASTELLINI S.p.A. stands behind its products warranting safety, reliability and performance.
The warranty is valid only under the following terms:
• The conditions given on the warranty certifi cate are observed.
• Performing yearly scheduled maintenance.
• The equipment is used only as instructed in this manual.
• The electrical wiring in the room in which the equipment is installed must conform to I.E.C. 60364-7-710 (standards for electrical wiring in medical
and dental offi ces).
2
• A 3x1.5 mm line protected by a bi-polar cut-out that conforms to applicable standards (10 A, 250 V, cut off power at least 6000 A, distance between
contacts at least 3 mm) must be used to feed the equipment.
ATTENTION!
The color of the three wires (POWER, NEUTRAL and EARTH) should satisfy the requirements of current standards.
• Installation, repairs and, in general, any other operations requiring the casing to be opened are to be performed exclusively by personnel authorized
by CASTELLINI.

1.2.4. Disposing the equipment When no longer used

As set out in Directives 2002/95/ EC, 2002/96/ EC and 2003/108/ EC, on the restrictions of the use of certain hazardous substances in electrical and
electronic equipment along with collection, treatment, recycling and disposal of waste electrical and electronic equipment the latter must be treated
as municipal waste, therefore sorted and collected separately. When new equipment of equivalent type is purchased the waste equipment should
be returned to the distributor on a one-to-one basis for disposal. As far as reuse, recycling and other forms of waste recovery mentioned above are
concerned, the manufacturer is responsible for the actions specifi ed by individual local laws.
Effi cient collection of sorted waste separately to recycle and treat waste electrical and electronic equipment aids in preventing negative environmental
impacts while protecting human health.
In addition it facilitates recycling of the materials used to construct the equipment.
Illegal waste disposal carries heavy fi nes defi ned by local laws.
WARNING!
The crossed out M.W.B.eled bin placed on the equipment indicates that the waste equipment must be collected separately from other wa-
ste.

1.3. Safety rules

WARNING!
• All equipment is permanently installed.
Depending on the type of chair the unit comes with, refer to the installation DATA given in paragraph "Specifi cations".
CASTELLINI S.p.A shall not be held liable for any personal injury or equipment damage resulting from failure to heed the precaution
given above.
• Floor conditions.
The fl oor (continuous) should meet the load-bearing capacity set forth by DIN 1055, sheet 3. The weight of the dental unit including a 190 kg patient
is about 350 kg/sq.m.
• The technician not authorized by
manufacturer shall assume liabilities in an identical manner as the manufacturer.
CASTELLINI S.p.A shall not be held liable for any personal injury or equipment damage resulting from failure to heed the precaution
given above.
• Dental chair.
The maximum chair capacity is 190Kg. This weight must never be exceeded.
• Tray holders.
The maximum weights that can be held must never be exceeded:
- Instrument tray attached to the instrument board maximum allowable load 2 Kg, evenly distributed.
- Instrument tray attached to the instrument board maximum allowable load 1 Kg, evenly distributed.
- Auxiliary instrument tray, maximum allowable load on tray 3.5 Kg (no x-ray fi lm viewer) or 2.5 Kg (with x-ray fi lm viewer).
• Connections to external instruments
The equipment can be hooked up only to other instruments that bear the CE mark.
• Electromagnetic interferences.
Use of electrical equipment that does not comply to standard I.E.C. 60601-1-2 in the offi ce or nearby may cause electromagnetic or other types of
interferences resulting in dental unit malfunctions.
In these cases, shut off power to the dental unit before using this equipment.
• Replacing the chucks.
Operate the turbine release and contra angle only once the chuck has come to a complete stop. On the contrary, the locking system will wear down
and the chucks can slip off causing injury. Use only high quality chucks with gauged diameter attachment. To check the state of the locking system,
make certain the chuck is fi rmly secured to the instrument every day before starting work. Locking system defects caused by misuse are easily
identifi ed and not covered by the warranty.
• Patients with pace makers and/or hearing aids.
When treating patients with pace makers and/or hearing aids, take into consideration the effects the instruments may have on pace makers and/
or hearing aids. Carefully read technical-scientifi c information available on this subject.
• Implants.
If the dental unit is used for implant operations using separate equipment designed for this purpose, shut off power to the dental chair to avoid
unwanted movements resulting from faults and/or accidental start up of the controls.
• Do not forget to turn off the offi ce's water supply and master switch on the equipment before leaving the surgery.
• The equipment is not protected against liquid penetration (IPX O).
SKEMA 6
- OPERATING INSTRUCTION
CASTELLINI who alters the product replacing parts or components with ones different from those used by the
GB EN 87 87 87