Renkforce RF-WM-110 Mode D'emploi page 3

Operating Instructions
RF-WM-110 Vertical 2.4 GHz Wireless Mouse
Item No. 2254922
Intended Use
This product is an ergonomic right-handed mouse. It helps reduces wrist strain and allows you
to make wider movements using your whole arm. The vertical design mimics a handshake
allowing your hand to wrap around the mouse without twisting your wrist.
Please allow up to 1 week for your hand and arm to get used to the vertical mouse design.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged. In
addition, improper use can result in short circuits, fires, or other hazards. Read the instructions
carefully and store them in a safe place. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery Content
• Mouse
• USB nano receiver
• 1 x AA alkaline battery
• Operating instructions
Up-to-Date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with the exclamation mark in the triangle is used to indicate important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety Instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General Information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the appliance from extreme temperatures, direct sunlight, strong jolts,
high humidity, moisture, flammable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Consult an expert when in doubt about the operation, safety or connection of
the appliance.
• Maintenance, modifications and repairs must only be completed by a technician
or an authorised repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) LED light
• Attention, LED light:
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
c) Batteries
• Correct polarity must be observed while inserting the battery.
• The battery should be removed from the device if it is not used for a long period
of time to avoid damage through leaking. Leaking or damaged batteries might
cause acid burns when in contact with skin, therefore use suitable protective
gloves to handle corrupted batteries.
• Batteries must be kept out of reach of children. Do not leave batteries lying
around, as there is risk, that children or pets swallow them.
• Rechargeable batteries must not be dismantled, short-circuited or thrown into
fire. Never recharge non rechargeable batteries. There is a risk of explosion!
Operating Elements
1
2
3
1 Left click
2 Forward
3 Backward
4 Right click
5 Scroll click-wheel
6 Power switch ON/OFF
7 DPI button
8 Battery compartment (inside)
9 USB receiver slot (inside)
10 Optical sensor
11 Compartment cover
Operation
a) Insert Battery
• Remove the compartment cover (11).
• Insert one AA battery into the battery compartment (8), matching polarity as shown inside.
• Replace the compartment cover (11).
b) USB Receiver
There is a storage slot (10) for the USB nano receiver located next to the battery.
• Connect the receiver to an available USB port on your computer.
• The computer will detect the new hardware and automatically install the required drivers.
If you do not use the product for extended periods of time, disconnect the receiver
from the USB port on your computer and store it the receiver slot (9).
c) Mouse
The base of the mouse may leave marks or scratches on delicate surfaces.
• Slide the power switch (6) to the ON position, the mouse and USB receiver will automatically
connect.
• To preserve battery life when not using the mouse, slide the power switch (6) to the OFF
position.
4
5
6
7
8
9
10
11