Assembly And Adjustments - DeWalt D25951 Traduction De La Notice D'instructions Originale

EngLIsh
Wear ear protection.
Wear eye protection.
Date Code Position (Fig. A)
The date code 7 , which also includes the year of manufacture,
is printed into the housing.
Example:
2018 XX XX
Year of Manufacture
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
On/off switch
1
Main handle
2
Chisel position index collar
3
Tool holder/sleeve
4
Side handle
5
Tool tag mounting holes
6
Date code
7
Intended Use
Your heavy-duty demolition hammer is designed for heavy-duty
demolition, chipping and chasing applications.
DO nOt use under wet conditions or in the presence of
flammable liquids or gases.
Your heavy-duty demolition hammer is a professional
power tool.
DO nOt let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Soft Start Feature
The soft start feature allows the impact rate to build up more
slowly, thus preventing the chisel or point from "bouncing"
around on the masonry when starting up.
Active Vibration Control
The active vibration control neutralises rebound vibration from
the hammer mechanism. Lowering hand and arm vibration,
it allows more comfortable use for longer periods of time and
extends the life of the unit.
20

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Always wear gloves when changing
accessories. The exposed metal parts on the tool and
accessory may become extremly hot during operation.
Inserting and Removing SDS MAX Accessories
(Fig. C)

WARNING: Do not apply lubricant to the machine.
This machine uses SDS MAX chisels (refer to the inset in Figure C
for a cross-section of a chisel shank).
Only D WALT recommended accessories should be used with
e
this product.
1. Clean the chisel shank.
2. Insert the chisel shank into the tool holder/sleeve
Press and turn the chisel slightly until the sleeve snaps
into position.
3. Pull on the chisel to check if it is properly locked. The
hammering function requires the chisel to be able to move
axially several centimetres when locked in the tool holder.
4. To remove a chisel, pull back the tool holder/sleeve
pull the chisel out of the tool holder.
Indexing the Chisel Position (Fig. D)
The chisel can be indexed and locked into 12 different positions.
1. Insert the chisel as described above.
2. Rotate the chisel position index collar
the arrow until the chisel is in the desired position.
Fitting and Adjusting the Side Handle (Fig. E)

WARNING: Always operate the machine with the side
handle properly mounted.
The side handle 5 can be mounted on the front of the machine
to suit both RH- and LH-users.
1. Unscrew the side handle clamp knob
2. Slide the side handle assembly onto the machine locating
the steel ring in the mounting area
10
position of the side handle is between head and middle of
the tube.
3. Adjust the side handle 5 to the desired angle.
4. Slide and rotate the side handle to the desired position.
5. Lock the side handle in place by tightening the clamp
knob 9 .
D WALT Tool Tag Ready (Fig. A)
e
Optional Accessory
Your hammer comes with mounting holes
for installing a D WALT Tool Tag. You will need a T20 bit tip to
e
install the tag. The D WALT Tool Tag is designed for tracking and
e
4 .
4 and
in the direction of
3
9 .
. The correct
8
6 and fasteners