Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
•
Mount the machine on a non-slip and level surface (risk of tipping).
•
Avoid abnormal posture. Provide a safe standing position and keep at any time the balance.
•
Be observant. Attend to what you do. Start working with rationality. Do not use the device when you are tired or under the
influence of drugs, alcohol or medicaments. One moment of carelessness when using the device can result in serious injuries.
•
Wear suitable work clothes:
- do not wear loose-fitting clothes or jewellery; they can catch in moving parts.
- Safety shoes
- wear a hair-net if your hair is long
•
Wear protective clothing:
- ear protection (Sound intensity level at workplace can exceed 85 dB (A))
- safety goggles
- Protective gloves
- Dust protection mask when carrying out works that produce a lot of dust
•
Keep your workplace in an orderly condition! Untidiness can result in accidents.
•
Take into consideration environmental influences:
- Do not use the device in moist or wet ambience.
- Do not expose the radial tile cutter to rain.
- Provide for good illumination.
- Do not use this machine near inflammable liquids or gases.
•
Never leave the machine unattended.
•
Children and youngsters less than 18 years of age and people who have not read the operating manual must not operate the
machine.
•
Keep other persons away.
•
Do not allow other persons, especially children, to touch the tool or cable.
•
Keep them away from your working area.
•
Use a lifting device if the weight of the workpiece exceeds 10 kg.
•
Assume a working position where you are always to the side of the cutting-off wheel outside of the cut plane.
•
Do not overload the machine! You work better and safer in the given performance range.
•
Only operate the machine with complete and correctly attached safety equipment and do not alter anything on the machine that
could impair the safety.
•
Do not use any cracked diamond cutting-off wheels as well as cutting-off wheels with segmented edge.
•
Do not use any cutting-off wheels which do not correspond to the indicated characteristics of this instruction manual.
•
Do not use any cutting-off wheels which have a maximum rotational frequency of less than 3000 revolutions per minute.
•
Always use diamond cutting wheels having an MPA overprint with a number.
•
Choose a diamond-tipped cutting-off wheel that is suited for the material to be cut.
•
Do not exceed the safe operating speed of the cutting-off wheel.
•
Do not perform dry cuts using cutting-off wheels that are designed for wet cutting.
•
Do not use the cutting-off wheel for grinding work, e.g. to grind the edge of a cut tile. Do not perform radius or round cuts.
•
Pay attention to that the water pump is covered with water. The use of other tools and other accessories can signify a risk of
injury for you.
•
Do not touch electrical components of the machine (e.g. switch) by wet hands.
•
Make sure that all plug-type connections are in a dry place and do not rest on the ground.
•
Keep water away from electrical parts of the power tool and from persons within the working area.
•
Switch the machine off and remove the mains plug from the socket when
- carrying out repair works
- maintenance and cleaning
- Elimination of failures (that includes also freeing a blocked cutting-off wheel)
- transport and storage
- Leaving the radial tile cutter (also for short-term interruptions)
•
Attention! Cutting-off wheel keeps running for a moment after switching off! Do not brake the cutting-off wheel with the hand
or lateral pressure.
•
Wait until the cutting-off wheel has come to a complete stop and then pull the mains plug out of the socket before carrying out
any adjusting, maintenance and cleaning work.
•
Maintain your radial tile cutter with care:
- Keep the tools sharp and clean to be able to work better and more safely.
- Follow the servicing instructions and the information about changing tools.
- Keep handles dry and free of oils and grease.
•
Check the machine for possible damage:
18
Publicité
Table des Matières
