Use And Maintenance - Atag WS9011EM Mode D'emploi Et D'installation

it to the ceiling using the screws A (Fig.3) in such a way that
it is in line with your hood and respecting the distance from
the ceiling indicated in Fig.2. Connect the fl ange C to the air
exhaust hole using a connection pipe (Fig.4).
Insert the upper fl ue into the lower fl ue. Fix the lower fl ue to
the hood using the screws B provided (Fig.4), extract the up-
per fl ue up to the bracket and fi x it with the screws B (Fig.3).
To transform the hood from a ducting version into a fi ltering
version, ask your dealer for the charcoal fi lters and follow the
installation instructions.
• Filtering version
Install the hood and the two flues as described in the
paragraph for installation of the hood in ducting version. To
assemble the fi ltering fl ue refer to the instructions contained
in the kit. If the kit is not provided, order it from your dealer
as accessory. The charcoal fi lters must be fi tted in the ducting
unit located inside the hood (Fig.7).

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to cook-
ing.
It is recommended to leave the appliance in operation for 15
minutes after cooking is terminated in order to completely
eliminate cooking vapours and odours.
The proper function of the cooker hood is conditioned by
the regularity of the maintenance operations, in particular,
the active carbon fi lter.
• The anti-grease fi lters capture the grease particles suspended
in the air, and are therefore subject to clogging according to
the frequency of the use of the appliance.
In order to prevent fi re hazard, it is recommendable to clean
the fi lter at a maximum of 2 months by carrying out the fol-
lowing instructions:
- Remove the fi lters from the cooker hood and wash them
in a solution of water and neutral liquid detergent, leaving
to soak.
- Rinse thoroughly with warm water and leave to dry.
- The fi lters may also be washed in the dishwasher.
The aluminium panels may alter in colour after several washes.
This is not cause for customer complaint nor replacement
of panels.
• The active carbon fi lters purify the air that is replaced in the
environment. The fi lters are not washable nor re-useable and
must be replaced at maximum every four months. The satura-
tion of the active carbon fi lter depends on the frequency of
use of the appliance, by the type of cooking and the regularity
of cleaning the anti-grease fi lters.
• Clean the fan and other surfaces of the cooker hood regu-
larly using a cloth moistened with denatured alcohol or non
abrasive liquid detergent.
• The illumination installation is designed for use during
cooking and not for prolonged general illumination of the
environment. Prolonged use of the illumination installation
notably reduces the duration of the bulb.
• Commands: (Fig.5)
Push-button A = on/off lights switch
Push-button B = on/off cooker hood switch. The appliance
switches on at speed level 1, If the cooker hood is on depress
the push-button for 2 sec. to switch off the cooker hood. If
the cooker hood is at speed level 1 it will not be necessary
to depress the push-button to switch the cooker hood off .
Decreases the motor speed.
Display C = indicates the motor speed level selected and
activates the timer.
Push-button D = switches on the cooker hood. Increases the
motor speed. Touching the key at 3rd speed, the intensive
function runs for 10' , then the appliance go back to work at the
original speed. During this function the display blinks.
Key E = The Timer times the functions on activation for 15
minutes, after which they are switched off . The Timer is deac-
tivated by re-pressing Key E. When the Timer is activated the
decimal point must fl ash on the display. The Timer cannot be
activated if the intensive speed is functioning.
The "clean air" function is activated by pressing key E for 2
seconds when the appliance is switched off . This switches the
motor on for 10 minutes every hour at the fi rst speed. During
functioning a rotary movement of the peripheral segments
must be visualised on the display. When this time has passed
the motor switches off and the fi xed letter "C" must be visu-
alised on the display until the motor re-starts after 50 minutes
for another 10 minutes and so on. Press any key apart from
the light keys to return to normal functioning. Press key E to
deactivate the function.
• Active carbon/grease fi lter saturation:Fig.5
- When display item C fl ashes, at a speed where it alternates
with the letter F (e.g. 1 and F), the grease fi lters must be
washed.
- When display item C fl ashes, at a speed where it alternates
with the letter A (e.g. 1 and A), the carbon fi lters must be
replaced.
After the clean filter has been positioned correctly, the
electronic memory must be reset by pressing button A for
approximately 5 seconds, until the indication F or A shown
on the display C stops fl ashing.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE
ABOVE WARNINGS.
- 12 -