Atex, Iecex, Ul, Csa; Explosion Proof (Ex D) Installation - Without Docking Station; Mechanical Installation Without Docking Station; Electrical Installation Without Docking Station - Dräger Polytron 8000 Serie Notice D'utilisation

en |

Explosion proof (Ex d) installation - without Docking Station

With a sealed conduit or approved cable gland, the instrument
can be connected to a Dräger control unit or a Programmable
Logic Controller (PLC).
If the 4 - 20 mA interface is used, the current between 0 and
3.5 mA must be monitored. Currents between 0 and 3.5 mA
can indicate a special state.
The instrument is designed to be installed in permanent
locations and is approved for use in hazardous, classified
areas.
®
Polytron 8100 EC-specific:
®
– Polytron 8100 EC is a combined intrinsically safe /
explosion proof instrument for continuous monitoring of
toxic gases or oxygen in the ambient air.
®
Polytron 8200 CAT-specific:
®
– Polytron 8200 CAT with catalytic DrägerSensor DQ or LC
is an explosion proof instrument for the continuous
monitoring of combustible gases and vapors containing
hydrocarbons and non-hydrocarbons (e.g. hydrogen or
ammonia) in ambient air.
®
Polytron 8310 IR-specific:
®
– Polytron 8310 IR with infrared DrägerSensor IR is an
explosion proof instrument for the continuous monitoring
of combustible gases and vapors containing hydrocarbons
in ambient air.
®
Polytron 87x0 IR-specific:
®
– Polytron 8700 IR with PIR 7000 is an explosion proof
instrument for the continuous monitoring of combustible
gases and vapors containing hydrocarbons.
®
– Polytron 8720 IR with PIR 7200 is an explosion proof
instrument for the continuous monitoring of carbon
dioxide.
3.5 Approvals

3.5.1 ATEX, IECEx, UL, CSA

See a sample of approval label on the fold-out page. There is
also a printout of the approval label inside the shipping box of
the instrument.
3.5.2 Marking
The marking is reproduced on a separate piece of paper
shipped with the instrument.
Serial Number key: The third letter of the serial number
specifies the manufacturing year: M = 2019, N = 2020, P =
2021, R = 2022, S = 2023, T = 2024, U = 2025, W = 2026, X =
2027, Y = 2028, Z = 2029, etc. (Letters G, I, O, Q are omitted)
Example: Serial Number ARMB-0001: the third letter is M,
which means that the unit was manufactured in 2019.
4 Explosion proof (Ex d) installation
- without Docking Station
Obey the safety statements mentioned in 1.3 Mechanical
installation!
12
4.1 Mechanical installation without
Docking Station
The instrument can be mounted for measuring gases in
ambient air or inside of a duct/pipe.
1. Use M6 (1/4'') bolts with hex socket caps to mount the
enclosure to one of the following options.
Option
Mounting on a flat surface
Mounting on a pole
Mounting on a duct/pipe
4.2 Electrical installation without docking
station
For recommended tightening torques and admissible wire
specifications see 17.3 Cable specifications.

4.2.1 Wiring tables

4-20mA / HART® interface
Pin Mark Function
1 PWR+ V+
2 PWR- V-
3 PWR- V-
To be used when the instrument is not pow-
ered by the control unit (separate power sup-
ply), see figures I3 and H1 on the fold-out
page.
4 4- 4 to 20 mA signal (Operation as source or
20mA sink)
5 PE Protective earth
Optional PE for relay connection. Connecting
PE together with the 4-20mA analog output
may cause ground loops.
Fieldbus interface
Pin Mark Function
1 Data- Signal Line A
A
2 Data- Signal Line B
B
3 GND Ground
4 SHIEL Cable Shield
D
Pin Mark Function
1 PWR+ V+
2 PWR- V-
Instructions for use
Accessory
Drilling template: 4544299
Additionally for Polytron
87x0 IR: Spacer 6812617
Pole mount kit: 4544198
Duct mount kit: 6812725
®
For Polytron 87x0 IR::
6812300
®
|
Dräger Polytron 8000 Series
®