Main Unit; Automatic Pairing; Manual Pairing - Sharp HT-SBW182 Manuel De L'utilisateur

Masquer les pouces Voir aussi pour HT-SBW182:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 31
AUX IN
A. Use a RCA to 3.5mm audio cable (not included) to connect the TV's
audio output sockets to the AUX IN socket on the unit.
B. Use a 3.5mm to 3.5mm audio cable (not included) to connect the TV's
or external audio device headphone socket to the AUX IN socket on
the unit.
TIP:
When you use the headphone output on the TV set, you will be able to
adjust the volume level directly using the TV remote control.
EU
UK
EU
UK
Connect to Power
• Before connecting this device to power, ensure you have completed all
other connections.
• Risk of product damage! Only use the supplied mains adaptor as failure
to do this may result in a safety risk and/or damage to the unit.
• Connect power adapter to the DC IN socket of the unit and then connect
it into a mains socket.
• Should you need to change the power adaptor plug type follow the
instructions below:
1. Remove the current AC plug adaptor by pressing plastic clip on the
left side and at the same time rotating the AC plug adaptor in an anti-
clockwise direction until it pops out of position.
~AC IN
DC IN
2. Now insert the correct AC plug adaptor by locating it into the AC power
adaptor socket and rotate clockwise until you hear a click confi rming
that it is locked in position.
• Use the power cord to connect the subwoofer to the mains socket.
Pairing the Wireless Subwoofer with the

Main Unit

Automatic pairing

The subwoofer and soundbar will automatically pair when both units are
plugged into the supply and turned on. No cable is needed for connecting
the two units.
– When the subwoofer is pairing with the main unit, the Pairing Indicator
will fl ash fast.
– When the subwoofer is paired with the main unit, the Pairing Indicator
will light up.
NOTE:
– Do not press the PAIR button on the rear of the subwoofer, except for

manual pairing.

– If the automatic pairing fails, pair the subwoofer with the main unit
manually.
Manual pairing
1. Press the PAIR button on the rear of the subwoofer, subwoofer's red
light will fl ash 2x.
2. Reset the soundbar - long press (5s) power key when Soundbar is in
LINE mode. Than soundbar will reset and standby.
3. Power on soundbar. Soundbar will search and pair subwoofer
automatically.
NOTE:
– If the wireless connection fails again, check if there is confl ict or strong
interference (for example, interference from an electronic device) around
your location. Remove these confl icts or strong interferences and repeat
the above procedures.
– The subwoofer should be within 6m of the soundbar in an open area.
– If a device is connected via HDMI (CEC active), the main unit and the
subwoofer will switch on automatically when the external device is
switched on.
Basic Operation
Standby/ON
• When you fi rst connect the unit to the main socket, the unit will be in
STANDBY mode.
• Press the
button on the remote control to switch the main unit ON
or OFF.
• Disconnect the main plug from the main socket if you want to switch the
unit off completely.
– When the unit has no input signal for over 15 minutes, it will automati-
cally switch to Standby mode.
Select Modes
Press the
button on the unit repeatedly or press the
the remote control to select the desired mode.
Adjust the Volume
– Press the + / - buttons on the unit or on the remote control to adjust the
volume.
– If you wish to turn the sound off , press the
control. Press the
button again or press the +/- buttons on the unit or
on the remote control to resume normal listening.
EN
/ button on
button on the remote

Publicité

Table des Matières
loading

Table des Matières