Functional.overview; Installation.instructions; Installing The Control - Becker S50II Notice D'utilisation

Function
Setting.mode.(Up/Down.in.deadman's.mode)
Self-locking.in.Up.direction
Self-locking.in.Down.direction
External.triple.pushbutton
Slack.cable.input./.Emergency.stop
Pulsed.input.Up/Stop/Down/Stop.(IMP)
Automatic.closing.(AWZ)
Partial.opening
Pneumatic.switching.rail.(USA/DW)
Electrical.switching.rail.(USA/EL)
Switching.rail.change-over:.1.2.kOhm/8.2.kOhm
Optoelectronic.switching.rail.from.FRABA.(OSE)
Light.barrier.(LS)
Traffic.light/Door.status.display
Yard.light
Warning.light.(RELAY.1)
LED.for.power.supply.(+UB)
LED.for.ascent.(OPEN)
LED.for.descent.(CLOSED)
LED.for.operating.status.(Betr)
LED.for.malfunction.(Stör1,.Stör2)
LED.for.switching.rail.(USA)
LED.for.pre-limit.switch.(VES)
LED.for.redundancy.(PIC)
.Function.only.if.a.switching.rail.is.used
1)

Installing the control

1. Installing the control
The.control.device.is.intended.for.use.indoors.and.is.to.be.installed.at.the.desired.operating.height..The.housing.cover.with.the.
triple.pushbuttons.can.be.removed.during.installation.by.means.of.the.plug-in.connection.(connector.is.retained.and.engages.
audibly.when.fitted).
2. Installing the supply point
Mount.a.CEE.16A/6h.socket.beneath.the.control.(protect.with.x10A.-pole.rotary.current.overload.circuit.breaker),.or.con-
nect.the.control.via.a.permanently.laid.installation.cable..During.commissioning,.the.cover.can.be.screwed.on.with.just.two.
screws.so.that.it.is.laterally.offset.(open.housing.facilitates.operation.of.buttons).
Caution
During all wiring work, the system must be disconnected from the power by removing the CEE plug or
switching off the main switch. Observe the applicable VDE guidelines during installation.
3. Motor/control connection
The.drive.cable.(12-wire).must.be.connected.to.the.appropriate.terminals.in.accordance.with.the.connection.plan.(not.re-
quired.if.connection.has.already.been.carried.out.by.Becker)..The.terminal.designations.correspond.to.the.numbers.of.the.
drive.cable.wires.(without.wire.4.and.10).
The.fitted.CEE.plug.can.be.used.as.the.main.switch..If.the.control.is.connected.without.the.CEE.plug.(e.g..permanent.con-
nection),.a.main.switch.must.be.connected.into.the.mains.feed,.which.disconnects.all.the.poles.according.to.the.overvoltage.
category.III.
4. Installing a control card
Operation.is.only.possible.with.an.inserted.control.card..The.S50 II.door.control.can.be.retrofitted.or.upgraded.by.changing.
the.control.card..The.following.control.cards.are.currently.available:
•. Deadman's.control.card
•. Multicard.II.control.card
For.the.card.functions,.please.refer.to.the."Functional.overview".or.the.relevant.operating.instructions..Disconnect.the.control.
from.the.power.before.changing.the.card..Make.sure.that.the.contact.pins.fit.snugly.
Attention
Relevant precautions must be taken when handling static sensitive components
Functional overview
Installation instructions
Deadman's.card
X
X
X
X
X
X
X
X
Multicard.II
X
X
X 1 )
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
DE
GB
FR
NL
11