Coleman HWOD 2302-A Série Mode D'emploi page 7

Use and Operation (continued)
SHUTTING OFF THE HEATER
1. Turn the control knob clockwise to the "OFF" position.
2. Switch off the power button on the display panel.
3. Turn the main power switch to "OFF" position (available on model 2302-A only).
IMPORTANT: User must not change the order of the shut-off-operation sequence. Alwasy shut off the burner and
gas supply by turning the control knob to the "OFF" position first, then switch off the power button.
STOPPING THE HEATER TEMPORARILY
Due to safety reasons, there's no switch to pause the water flow while taking a shower. You can only shut off the main burner by turning the control knob
clockwise back to the ignition position " PILOT" to conserve gas, the pilot light remains lit, the pump & water keeps running. To resume heating the water, turn
the control knob counter-clockwise to a setting between "MAX" & "MIN" position.
Or you may shut off the heater completely by following steps in above section "Shutting Off the Heater", then restart the whole ignition process illustrated in
section "Lighting the Heater".
CLEANING INSTRUCTIONS
1. In a clean container mix two-gallons (7.5 L) of water with 12
oz. (340 g) of calcium, lime, and rust remover (available at the
cleaner section of hardware, general merchandise and food
stores).
2. Place the pump and shower in the container with the water/
solution. The label "This Side Up" on pump should be facing up.
3. Start the heater by following instructions in section "Lighting the
Heater" and turn the control knob to a "warm" setting.
4. Circulate the water/solution through the heater for 2 minutes,
then turn off heater by turning the knob clockwise to the "off"
position and switching off the power button on display panel.
5. Dispose of the cleaning solution in a sink or other drain, do not
dump on the ground.
6. Fill container with 2.4 gallon (9 L) of clean water.
7. Place the pump and shower in the container with the water.
8. Turn the heater on and circulate the clean water through the
water heater for 2 minutes at the "cool" setting,
9. Turn the heater off.
10. Repeat steps 6-9 with another batch of clean water.
11. Clean the screen at the pump water inlet to remove the residue that may clog the pump. See maintenance section on page 8 for instructions.
CHARGING USB COMPATIBLE DEVICES (Available on model 2302-A only)
You may charge 2 mobile phones at the same time by connecting the phones to the USB ports on the
heater. The capacity of the rechargeable battery inside the heater is 2000 mAh, which could charge a
1570 mAh mobile phone (iPhone 5s) one complete cycle.
IMPORTANT: USB ports only work when the Main Power Switch is turned on. Do not connect
devices to the USB ports on the heater when the heater is in operation or is still hot to touch. Do
not connect devices to the USB ports on the heater if there's a "LOW BATTERY" indication on the
Display Panel (see chart of indicators in section
"Chart of Indicators"). Do not charge devices whose battery capacity exceeds 1700 mAh.
CHANGING TEMPERATURE DISPLAY
(available on model 2302-A only)
Current water temperature is shown on Display
Panel, cycle through the Celsius / Fahrenheit
display by pressing the button repeatedly
on the Display Panel.
OFF
Water / solution cycle
Clean water cycle
CHANGING SHOWER SPRAYS
(available on model 2302-A only)
The shower features aerated, full and
fine sprays. Change the spray by rotating
the dial on the shower head. You may
shut-off the water by rotating the dial on
shower head to OFF position.
NOTE: When the heater is powered on, turning the dial on the shower
head to "OFF" position will trigger the LOW WATER FLOW warning and
shut off the unit. Please ensure shower head is open before restarting.
Warm
IGNITE
IGNITE
OFF
Cool
OFF
7