Customization Of Automatic Oiler Output; Malfunctions; Material Jam In The Machine; Light Barrier Covered When - Intimus 175 hybrid 297-1CH Instructions D'opération

GB
3 .7 Customization of automatic
oiler output
The automatic oiler output can be adapted to your re-
quirements:
a) Ample Mode: 25% more oil is transported to
the cutting mechanism than in normal mode.
b) Normal Mode - default setting
c) Scarce Mode: 25% less oil is transported to the
cutting mechanism than in normal mode.
Ample Mode
(+25%)
Normal Mode
Scarce Mode
-25%
1 Forwards button
2
Functions button
3
Reverse button
fig. 5 Customization of automatic oiler output
For customizing the automatic oiler output proceed as
follows:
1 . The machine must be switched off.
2 . Open the door.
3 . Press and hold the forward button (fig. 5/1) and the
reverse button (fig. 5/3) simultaneously.
4 . Additionally press and let go of the function but-
ton (fig. 5/2).
¾ All LED indicators on the display light up.
5 . Let go of the forward button and the reverse but-
ton.
¾ Now you are in the memory mode.
6 . Press the forward button twice (fig. 5/1).
¾ Now you are in the customization mode for au-
tomatic oiler output.
¾ The LED indicator on the left side flashes show-
ing the current settings.
7 . Press the function button (fig. 5/2) so often until
the needed oiler output mode comes on.
¾ Each time you press the function button the
output mode changes (Ample, Scarce, Normal)
8 . Press the reverse button (fig. 5/3).
¾ Now you are again in the memory mode.
9 . Press the function button.
¾ The selected settings are saved.
¾ The machine switches off.
10 . Close the door.
If you want to continue shredding turn the machine
on: press the function button (fig. 5/2) briefly.
16
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
4

Malfunctions

4 .1 Material jam in the machine

(auto-reverse-funktion)
CAUTION!
Danger of injury!
Remove the material carefully because the-
re is the risk of being injured by the sharp
cut surfaces.
If a jam is caused by too much material being fed in the
1
following happens:
2 • The cutters jam, then run in reverse for a short time
(material is released) and stop.
• The motor switches off.
• The control display
3
as follows:
Jam on the paper side (wide feed slot, fig . 1/2)
000144
1 . Remove any returned paper or briefly press the
forward button (fig. 3/2).
¾ The cutters now run forwards automatically and
shred the remaining paper in the cutters. During
the forward run the forward button (fig. 3/2)
LED display
(fig. 3/9) goes out.
2 . Continue shredding with less paper.
Jam of the data media side (narrow feed slot,
fig . 1/1)
1 . Press the forward button (fig. 3/2) briefly.
¾ The material is once again fed to the cutting sys-
tem.
2 . If necessary, switch the cutters manually alterna-
tely from forward to reverse until the material has
gone through completely and been shredded.
4 .2 Light barrier covered when ma-
chine turned on
Should there still be material in the feed slot when the
machine is switched on the control display
comes on.
1 . Remove the material or
2 . Press the forward button (fig. 3/2) briefly.
¾ The existing material is fed to the cutters and
shredded.
(fig. 3/9) comes on. Proceed
comes on. The control display
93901 5 01/18
(fig. 3/9)