User Maintenance Instructions - BaBylissPro FOILFX02 FXFS2 Série Directives D'utilisation

WARNING:
Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by Conair
Corporation, the manufacturer of this product and the party responsible for
compliance, could void the user's authority to operate the equipment.
FOR DIRECT PLUG-IN OPERATION
Make sure shaver is off. Connect charging jack into the receptacle at the bottom
of shaver and plug the adapter into power outlet.
ON/OFF SWITCH
To operate, simply slide switch to the ON (I) position. To stop operation, set to
the OFF (O) position.
FXFS2 Series IB-15500E.indd 5-6 FXFS2 Series IB-15500E.indd 5-6
VERY IMPORTANT: Cutters must be cleaned and oiled on a regular basis
for proper functioning. Failure to regularly clean and oil the cutters will
void the warranty.
BASIC INSTRUCTIONS FOR USE
1. Men whose skin is sensitive or easily irritated by shaving, or who suffer
from a skin allergy, should test one section on the leg or arm before using
the shaver.
2. Remove the protective cover and turn on the unit to start shaving. Hold the
shaver at a right angle to the area that you want to shave and run the double
shaving foil carefully along your skin. Tip: In general, we recommend that
you shave against the direction of hair growth, as this is the best way to
trim the hair. Pull your skin tight, with your fingers in inaccessible areas, to
achieve optimum results.
3. Switch the shaver off each time after shaving and clean it.
4. Do not push the shaver on the skin too hard as it could cause irritation, make
the shaver warm and prevent a perfect shave.
5. Please note that it takes 2 to 4 weeks for your skin to adapt to a shaver, so
please do not change shaving instruments in this period of time.
6. If hair is longer than 1/32" begin by cutting the hair down first with a trimmer,
than use shaver for a smooth close shave.
USER MAINTENANCE
INSTRUCTIONS
TAKING CARE OF YOUR SHAVER
Do not remove the shaving foil unit while the shaver is switched on. Always
switch the shaver off!
Ensure that no water gets into the inside of the shaver to avoid the risk of an
electric shock when it is back in operation.
Never press on the cutting blades or the shaving foil and do not touch them
with hard objects as this can cause irreparable damage to the shaver or parts.
Be careful when dealing with the blades, as they are very sharp. Risk of injury!
When cleaning, do not apply any detergents or scouring agents and do not use
any abrasive or sharp objects. They can cause irreparable damage to the shaver.
2021/3/25 10:46 AM 2021/3/25 10:46 AM