Maintenance; General; Daily Cleaning - Hatco Krampouz KCMG-1RND Manuel D'installation Et D'utilisation

English

General

Gas Crepe Makers are designed for maximum durability and
performance with minimum maintenance.
WARNING
Improper installation, operation, or maintenance of this
equipment may result in property damage, serious injury,
or death. Do not operate or service this equipment before
reading and understanding the contents of this manual!
Turn temperature control to off ("0") position, close gas
shut-off valve, and allow unit to cool before performing
any cleaning, adjustments, or maintenance.
FIRE OR EXPLOSION HAZARD:
• Inspect moveable gas connector regularly. Replace
immediately if any signs of wear are present.
• Verify flexible gas tubing has not exceeded its
expiration date. Replace immediately if expired.
• Do not twist moveable gas connector.
• The unit and its individual gas shut-off valve must be
disconnected and isolated from the gas supply piping
system during any pressure testing of the system at
test pressures in excess of 1/2 psi (3.5 kPa.).
• This unit must be isolated from the gas supply piping
system by closing its individual gas shut-off valve
during any pressure testing of gas supply piping
system at test pressures equal to or less than 1/2 psi
(3.5 kPa).
• If the information in these instructions is not followed
exactly, fire or explosion may result causing property
damage, personal injury, or death
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to explosion
or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
conditions. Genuine Hatco Replacement Parts are
specified to operate safely in the environments in
which they are used. Some aftermarket or generic
replacement parts do not have the characteristics that
will allow them to operate safely in Hatco equipment.
Do not steam clean or use excessive water on unit.
This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged or
saturated with water.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
CAUTION
BURN HAZARD: Allow unit to cool before performing any
cleaning, adjustments, or maintenance.
Form No. KCMGM-1219

Daily Cleaning

To preserve the finish of the unit as well as maintain
performance, it is recommended that the unit be cleaned daily.
Submerging or saturating unit with water may cause
serious injury, will damage the unit, and void unit warranty.
For steel surfaces, use non-abrasive cleaners and cloths
only. Abrasive cleaners and cloths could scratch finish of
unit, marring its appearance and making it susceptible to
soil accumulation.
Do not use harsh chemicals such as bleach, cleaners
containing bleach, or oven cleaners to clean this unit.
Do not attempt to cool griddle quickly, such as by rinsing
or immersing in water. Damage to griddle will occur.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
1. Perform the "Shutdown" procedure in the OPERATION
section of this manual, and allow the unit to cool.
WARNING! Always close gas shut-off valve when unit
is not in use.
2. Wipe the griddle using a clean, non-abrasive cloth.
NOTE: A cleaning pad for spreading the oil and cleaning
the griddle surface is available as an accessory. See
OPTIONS AND ACCESSORIES for details.
3. Wipe the frame of the unit with a non-abrasive cloth
dampened in warm water and a mild soap. Stubborn stains
may be removed with a good stainless steel cleaner. Hard
to reach areas should be cleaned with a small brush and
mild soap.
4. Wipe the frame of the unit thoroughly using a non-abrasive
cloth dampened in warm water only.
5. Dry the frame of the unit using a clean, dry, non-abrasive
cloth.
NOTE: Oil and fats will build up on the griddle surface over time.
This eventually will begin affecting the performance of
the Crepe Maker. An abrasive stone is available as an
accessory (see OPTIONS AND ACCESSORIES). Use
the abrasive stone to strip the griddle on a regular basis
to maintain performance of the unit. The "Seasoning
the Griddle(s)" procedure must be performed after
stripping the griddle.
11

MAINTENANCE

WARNING
NOTICE