Lane Departure Warning System; Frequently Asked Questions - Polaroid PD-G55H Manuel D'utilisation

7 Lane Departure Warning System

* The purpose of the Lane Departure Warning System is to alert the driver if the vehicle strays over
the white line, to prevent the driver from going off of the road.
* Please use the Lane Departure feature as an extra precaution but do not rely solely on it as alerts
can vary due to road condi-tions, road markings, and weather conditions.
* Please note that the LDWS engages once the vehicle speed is 45 MPH or above.
For optimal use:
1. Position the dash cam in the middle of your windshield, under the rear view mirror.(See other
mounting options below)
2. Access the Menu using the toggle button and go to Lane Departure, press the toggle button to
engage the feature
3. Select the sensitivity level (low, medium , or high), press the toggle button to set 2 white bars will
appear in the screen once you toggle back to the main screen,
4. Adjust the dash cam so that the white bars are parallel with the road. You may need to turn the
camera slightly to the right or left, as well as tilt it up or down to achieve this.
* Please check with your local DMV office for specific laws regarding mounting products on the
windshield.
* In the event you need to position the dash cam away from the middle of your windshield, please
keep the Dash Cam horizon-tally balanced, and the road inside the 2 white bars of LDWS function.
(make sure the zoom is all out at x1)

8 Frequently Asked Questions

Q: Where to place the Dash Cam?
A: Model with GPS system: for best GPS signal and LDWS result, please mount the Dash Cam in the
middle of windshield, under the rear view mirror. If not in the middle, please also keep the Dash Cam
horizontally balanced, and the road inside the 2 white bars of LDWS function. However, please consult
your local DMV for legal Dash Cam position.
A: Model without GPS system: we recommend that you mount the Dash Cam as close to the center of
windshield as possible. However, please consult your local DMV for legal Dash Cam position.
Q: Why the Dash Cam stops recording after some time?
A: Your micro SD card may be full and need to be formatted before using again. 1080P HD videos are big in
size and G-sen-sor locked videos cannot be erased automatically. So we recommend you to manually
format your card every 1-2 weeks.
Q: Why recommend Class 6 micro SD card or above?
A: 1080P HD video has a bigger data flow and hence needs a micro SD card with faster writing speed. If
Class 4 cards are used, they may cause the Dash Cam to freeze or other video recording/erasing issue.
Q: How do I turn off the screen/audio during recording?
A: To turn off the screen, just press the MODE button once during recording. To turn Audio Record, just
press the POWER button shortly. Please note that these 2 buttons do not interrupt recording.
Q: How to lock / record emergency videos?
A: During recoring, a sudden force impact on Dash Cam will trigger its G-sensor to automatically lock the
current video. A key-like icon will appear on upper left corner of screen and this locked video CANNOT be
erased by Loop Recording function. For manual lock/record, please press REC or ensure Dash Cam is in
recording status, and then press Menu (M) Button.
Q: For how long will my battery last after a full charge?
A: Our batteries usually take 2-3 hours to fully charge. But this can happen simutaneously when Dash Cam
is plugged into your car and working/recording. After a full charge, our batter can last 15 - 60 mins,
depending on the model and temperature.
Q: How do I record videos?
A: All Dash Cams are programmed to Automatic Record. That is when Dash Cam is plugged into your
cigarette lighter and engine starts, the Dash Cam will start recording. It stops 3-10 secs after your engine
stops. Of course, you can always manu-ally start/stop recording by pressing the REC button.
22