Cleaning Instructions; Before First Use; Cleaning And Sanitization After Each Use; Before Each Use - Lansinoh SMARTPUMP Mode D'emploi

Lansinoh Smartpump Breast Pump Parts
® ™
Item
A. Smartpump Tubing
™
A1 Silicone Tubes 300 mm (2)
A2 Silicone Tube 600 mm
A3 Smartpump Tubing Y Connector
™
A4 Smartpump Pump Connnector
™
B. Breastmilk Expression Set Includes:
B1 ComfortFit Breast Flange 25mm (2)
™
B2 ComfortFit Breast Flange 30.5mm (2)
™
B3 Smartpump Breast Flange Body (2)
™
B4 Smartpump Diaphragm (2)
™
B5 Smartpump Diaphragm Cap (2)
™
B6 White Valve (2 + 2 extra)
B7 5 oz (150 ml) Bottle (4 ), (2
B8 NaturalWave Slow Flow Nipples (2)
®
C. Storage Lids (4 ), (2 )
D. Smartpump AC Adapter/power cord
™
E. Wide Neck Bottle Holder (2)
B
B8
C
A
Two extra white valves are included. To order replacement parts please visit
www.Lansinoh.com/store.
8
Smartpump_Manual_CA_082317.indd 8-9
= Retail
= Insurance
Item Number
#53403
#53405
#53453
#50408
#53408
#53454
#53402
#53410
#53401
) #53451
#71027
#53450
#50409
#53452
B5
B4
A1 A3 A2
B3
E
B6
B7
D
A4

3. CLEANING INSTRUCTIONS

Unless otherwise instructed by your healthcare provider, follow these sanitizing and cleaning instructions.

3.1 Before First Use

1. Always wash and dry hands thoroughly with soap and water before handling the breastmilk
expression set.
2. Disassemble the breastmilk expression set and place parts in a large pot.
3. Cover the parts in water making sure there is room for all of the parts to float freely in the pot.
4. Bring the water to a boil and allow the parts to boil for 5 minutes.
5. After boiling remove the parts from the pot with tongs and place on a clean towel to dry,
covering the parts with a second towel.
6. Allow the parts to dry completely before assembly and use. Partially dried parts may affect
the operation of the pump.
7. Once parts are dry they can be stored in a clean plastic bin with a lid or in a clean plastic
zipper bag.

3.2 Cleaning and Sanitization after Each Use

1. Disassemble the breastmilk expression set, setting aside the tubing and connectors.
2. Rinse all parts with cold water immediately after each use. Place pump parts in a clean wash
basin used only for washing infant feeding equipment. Do not place pump parts directly in
the sink, because germs in sinks or drains could contaminate the pump.
3. Hand wash all parts of the breastmilk expression set using warm soapy water. A nipple
brush may be used to scrub the hard plastic pieces of the breastmilk expression set, but
should not be used on the soft silicone valve or diaphragm.
4. Rinse parts with running clean, warm water, or by submerging in fresh water in a separate
basin that is used only for cleaning infant feeding items.
5. Place parts in a pot and cover with water making sure there is room for all of the parts to
float freely in the pot.
6. Bring the water to a boil and allow the parts to boil for 5 minutes.
B1
7. After boiling remove the parts from the pot with tongs and place on a clean towel to dry,
covering the parts with a second clean towel. Place wash basin and bottle brush on a clean,
B2
unused dish towel or paper towel in an area protected from dirt and dust. Do not use a dish
towel to rub or pat items dry because doing so may transfer germs to the items.
8. Allow the parts to dry completely before assembly and use. Partially dried parts may affect
the operation of the pump.
9. Once parts are dry they can be stored in a clean plastic bin with a lid or in a clean plastic
zipper bag.
10. Clean wash basin and bottle brush. If you use a wash basin or bottle brush when cleaning
your pump parts, rinse them well and allow them to air-dry after each use. Consider washing
them every few days, either in a dishwasher with hot water and a heated drying cycle if they
are dishwasher-safe, or by hand with soap and warm water.

3.3 Before Each Use

1. Always wash and dry hands thoroughly with soap and water before handling the breastmilk
expression set.
2. Before assembling the breastmilk expression set, be sure that all of the parts are completely dry.
3. Visually inspect the individual components for cracks, chips, tears, discoloration or
deterioration. These may affect the functionality of the pump.
4. Should you have any questions or concerns about your parts please contact Lansinoh at
800-292-4794 for further guidance.
5. To purchase replacement parts for your pump please visit Lansinoh.com/Store
9
8/28/17 11:49 AM