Maintenance And Service; Maintenance And Cleaning - Bosch GSG 300 Professional Notice Originale

OBJ_BUCH-75-003.book Page 8 Wednesday, October 19, 2016 10:32 AM
8 | English
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
To switch on the power tool, press the On/Off switch 1 and
keep it pressed.
To lock the pressed On/Off switch 1, slide the On/Off switch
1 toward the rear.
To switch off the power tool, release the On/Off switch 1, or
when it is locked, briefly press the On/Off switch 1 and then
release it.
Working Advice
 Before any work on the machine itself, pull the mains
plug.
Saw Blades and Saw Blade Guides
Depending on the material thickness to be worked, various
saw blade guides and the corresponding saw blades can be
used. See the Accessories Overview for more details.
Base Plate
The foam rubber cutter can be used with or without the base
plate. The base plate is equipped with rollers, and allows for
easy and right-angled guidance of the cutter.
For cutting random forms and for cutouts, it is recommended
to work without the base plate.
Cutting Foam
For precise cuts, especially with soft foams and similar mate-
rials, work only with moderate feed. To not press the material
together or squeeze it apart too excessively while working.
Dismount the base plate for smaller cutouts. Puncture the ma-
terial using a knife or a pair of scissors, then insert the saw
blade guide into the opening und work the cutout.
For larger cutouts, select an entry opening large enough to in-
sert the saw blade guide with the mounted base plate. Pay at-
tention that no obstacles are on the bottom of the material.
Guide the power tool with moderate pressure alongside the
cutout line.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
1 609 92A 38G | (19.10.16)
The saw blade guide and the saw blades at regular intervals,
approx. after 8 hours of operation. Remove the saw blades
from the power tool for this and preferably clean the saw
blades with petrol. If required, use a scraper to clean the saw
blade guide. Apply a light coat of oil onto the saw blade guide
before assembling new or resharpened saw blades.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
People's Republic of China
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: 4008268484
Fax: (0571) 87774502
E-Mail: contact.ptcn@cn.bosch.com
www.bosch-pt.com.cn
HK and Macau Special Administrative Regions
Robert Bosch Hong Kong Co. Ltd.
21st Floor, 625 King's Road
North Point, Hong Kong
Customer Service Hotline: +852 2101 0235
Fax: +852 2590 9762
E-Mail: info@hk.bosch.com
www.bosch-pt.com.hk
Indonesia
PT Robert Bosch
th
Palma Tower 10 Floor
Jl. RA Kartini II-S Kaveling 6 Sek II
Pondok Pinang, Kebayoran Lama
Jakarta Selatan 12310
Indonesia
Tel.: (021) 3005 5800
Fax: (021) 3005 5801
E-Mail: boschpowertools@id.bosch.com
www.bosch-pt.co.id
Bosch Power Tools