Marshall CODE 100 Manuel Du Propriétaire page 5

FRONT PANEL FUNCTIONS (CONT.)
8. MASTER
Controls the overall volume level of your
CODE amplifier.
MASTER volume control settings are not
!
stored as part of a Preset.
9. PRESET
A Preset is a combination of preamp, power
amp & speaker models, with tonal settings
and FX: Chorus, Flanger, Tremolo, Delay
etc, stored to a single location within your
CODE amplifier's memory. This is like a
'snapshot' of the whole amplifier's settings
(excluding MASTER), which can be recalled
using the PRESET selector, or with the
optional CODE footcontroller.
Turn the PRESET selector to explore your
CODE amplifier's factory Presets.
10. EDIT
Use the EDIT selector to deep edit a Preset.
Push the EDIT selector to preview the
stored Gain, Bass, Middle, Treble & Volume
settings. Turn the EDIT selector to view the
SECTION SWITCHES (15 - 21)
The Section Switches represent different 'sections' in the guitar signal chain. This is the
route that a guitar signal travels through a conventional amplifier setup from the guitar to
the loud speaker(s).
19 18 17
REVERB DELAY
POWER AMP
20
15
STOMPBOX
ENGLISH
current Section Switch settings.
To discover how to edit a Preset, go to
!
'EDITING A PRESET' in this manual.
11. F/C
Use this jack socket to connect the
supplied 2-way footswitch for scrolling
through Presets, or to connect the CODE
programable footcontroller (PEDL-91009
sold separately).
12. MP3 PLAYER INPUT
Use this dedicated mini-jack socket to
connect an audio player to practice with or
jam along to music.
13. HEADPHONE OUTPUT
Use this mini-jack socket to connect
headphones for 'silent' practice. This can
also be used as a line out.
19 18 17
14. ON/OFF REVERB DELAY MOD
This is the mains power ON/OFF switch.
20
15
STOMPBOX
15 16 17 18 19 20
MOD
Pressing the Section Switches (#15 – #21 in
this manual) will activate (Red LED on) and
bypass (LED off) that Section.
PREAMP
CABINET
21
16
FRONT PANEL FUNCTIONS (CONT.)
15. PRE FX
This is where you will find FX that would typically plug into a conventional amplifier setup
between the guitar and the amplifier's input. These FX would typically be in pedal form,
and also known as 'stompboxes' . The 'stompbox' FX in the PRE FX section are:
Compressor
Compressor affects an audio signal's dynamic range. CODE's compressor decreases,
or 'compresses' , any part of your guitar sound that peaks above a certain threshold.
Any part of your guitar sound that remains below the threshold is unaffected.
Compressor can add clarity and consistency to your guitar sound whether clean or
overdriven. Compressor's editable parameters are:
PARAMETER
Tone
Ratio
Compression
Level
21
16
Distortion
CODE's stompbox Distortion's three Modes simulate solid-state Distortion and
Overdrive FX pedals. GUV Mode is a Marshall Guv'nor™ with Drive and Tone
controls. ODR & DIS Modes provide flavours of classic overdrive and distortion
stompboxes. Stompbox Distortion is particularly effective when used with classic
and vintage MST preamp models to provide more drive and sustain. Distortion's
editable parameters are:
Marshal l
21
PARAMETER
Mode
Drive
Tone
Level
'STOMPBOX' FX
VALUE RANGE DESCRIPTION
0 - 10 Adjusts the Compressor's higher and lower
frequencies.
0 - 10 Controls how much Compression is applied to a signal
above the threshold.
0 - 10 Adjusts the point at which Compression is applied to
the signal.
0 - 10 Controls the overall volume level of the Compressor.
VALUE RANGE DESCRIPTION
GUV, ODR & DIS Marshall Guv'nor, Classic OD pedal
& Classic Distortion pedal.
0 - 10 Controls the amount of Overdrive or Distortion
applied to the signal.
0 - 10 Adjusts the amount of upper mid and higher frequency
content in the Overdrive or Distortion before the
signal reaches the amplifier panel tone controls.
0 - 10 Controls Distortion's overall volume level.
ENGLISH
A: >>|<< A: >>|<<