Getting Started - Eccotemp CEL10 Manuel D'utilisation Et D'entretien

Phone: 866-356-1992 | Email: Support@eccotemp.com

Getting Started

1. Check box for damage. Damages caused in shipment must be reported immediately.
2. Make sure you have all the parts.
Please note: Included parts and accessories may vary depending on county and regulations.
qty. 1 -
Water heater
3. If using a standard garden hose, attach the 3/4" NPT to garden hose adapter to the fitting
marked 'Water Input". Use Sealant tape or other approved sealing method on the threads for a
secure, water tight fit. Check to make sure the screen inside the water inlet is in place and clean.
Then attach your water input/garden hose.
4. Install gas supply line and regulator to the portable tankless water heater. DO NOT OVER
TIGHTEN. OVER TIGHTING MAY CRACK THE GAS REGULATOR CAUSING A GAS LEAK! Check for
any gas smell before ignition! Make sure it is screwed all the way on.
5. Attach the water output to the fitting marked 'Water Outlet.' Do not over tighten.
6. Install two "D" cell batteries in the compartment on the bottom left of the heater. Check that
batteries are facing the correct direction.
7. Use the top tab on the portable tankless water heater to suspend from a mounted screw capable
of holding 15 kilograms. Place at a comfortable height without putting stress on the gas hose.
With 1/2" compression fitting adapter
8a. If your water heater comes with the 1/2"
compression fitting adapter first attach the adapter
to the gas input pipe using 2 wrenches, one on the
gas inlet pipe holding it in place and the other on
the adapter tightening it in place. Next, attach the
gas regulator hose to the LP tank using a wrench
to tighten. Finally use a wrench to hold the adapter
that's connected to the water heater in place
and connect the end of the regulator hose to the
adapter using another wrench. After connecting it's
imperative you inspect for gas leaks. See page 3 for
instructions on how to test for leaks.
THE L5, & L10 PORTABLE TANKLESS WATER HEATERS HAVE A 1/2'' TO 1/4" LH
ADAPTER IN THE HARDWARE PACK FOR ATTACHMENT OF THE LP HOSE TO THE
THIS ADAPTER MUST BE INSTALLED WITH THREAD SEALANT, A SPOOL OF
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS.
THIS MODEL IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
Support: Eccotemp.com/help-desk
qty. 1 -
qty. 1 -
Hardware pack 1/2" NPT to garden
hose adapter
WARNING!
GAS HOSE ADAPTER
HEATER.
SEALANT TAPE IS INCLUDED WITH THE HEATER.
MULTIPLE WRAPS OF SEALANT TAPE MAY BE
NECESSARY TO ASSURE COMPLETE SEAL.
ALWAYS CHECK FOR GAS LEAKS BEFORE USING HEATER.
AFTER EVERY USE.
Shop Online: eu.eccotemp.com/products
qty. 1 - 1/2"
Compression Fitting
and regulator
(Not available in all countries)
Without compression fitting
8b. Attach the gas regulator hose to the
LP tank and tighten the connection using a
wrench. Next attached the other end of the
regulator hose to the gas inlet pipe on the
water heater. Use a wrench to hold the gas
inlet pipe coming out of the water heater in
place and use another wrench to tighten the
hose connection to the gas inlet pipe. After
connecting it's imperative you inspect for gas
leaks. See page 3 for instructions on how to
test for leaks.
Store Locator: Eccotemp.com/locator
qty. 1 - Gas
hose
9