Napa 6-1122 Mode D'emploi page 2

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
This insTrucTion Man u al
con Tains iMporTanT safeTy
inforMaTion.
read This
in sTruc Tion
Manual
care ful ly and
un der sTand all in for Ma Tion
Be fore op er aT ing This Tool.
• Al ways operate, in spect and
main tain this tool in ac cor dance
with Amer i can Na tion al Stan dards
In sti tute Safe ty Code of Por ta ble
Air Tools (ANSI B186.1) and any
oth er ap pli ca ble safe ty codes
and reg u la tions.
• For safety, top per for mance and
max i mum du ra bil i ty of parts,
op er ate this tool at
90 psig, 6.2 bar max
air pres sure with 3/8"
di am e ter air
sup ply hose.
• Always wear impact­resistant
eye and face
protection when
operating or
performing
maintenance on this
tool.
• High sound levels can cause
permanent hearing loss.
Always use hearing
protection as
recommended by
your employer and
OSHA regulations
while using this tool.
• Keep the tool in ef fi cient
op er at ing con di tion.
• Operators and main te nance
per son nel must be phys i cal ly
able to han dle the bulk, weight
and pow er of this tool.
• Compressed air can
cause severe injury.
Never direct air at
yourself or others.
PLEASE REVIEW ALL WARNING INSTRUCTIONS PRIOR TO OPERATION. SAVE ThIS mAN U AL fOR fUTURE REf ER ENCE.
6-1122
Always turn off the air supply,
drain hose of air
pressure, and detach
tool from air supply
before installing,
removing, or adjusting
any part or accessory on this
tool, or before performing any
maintenance on this tool. Failure
to do so could result in injury.
Whipping hoses can
cause serious injury.
Always check for and
replace any damaged,
frayed, or loose hoses
and fittings. Do not
operate a damaged or worn tool.
Do not use quick­detach couplings
at tool. See instructions for correct
setup.
• Air­powered tools can vibrate
during use. Extended exposure
to vibration,
repetitive motions,
or uncomfortable
positions during use
may be harmful to
your hands and arms. Discontinue
use of tool if discomfort, tingling,
or pain occurs. Seek medical
advice before resuming use.
• Place the tool on the work
be fore start ing the tool. Do not
point or in dulge in any horse play
with this tool.
• Slipping, tripping and/or falling
while operating air tools can be
a ma jor cause of se ri­
ous in ju ry or death. Be
aware of ex cess hose
left on the walk ing or
work surface.
• Keep body work ing stance bal­
anced and firm. Do not over reach
when op er at ing the tool.
• Anticipate and be alert for sudden
changes in motion during use of
any power tool.
2
• Do not carry tool by the hose.
Pro tect the hose from sharp
ob jects and heat.
• Tool shaft may
con tin ue to ro tate
brief ly af ter throt tle is
re leased. Avoid di rect
con tact with ac ces so­
ries dur ing and af ter
use. Gloves will re duce the risk
of cuts or burns.
• Keep away from ro tat ing end
of tool. Do not wear jew el ry or
loose clothing. Se cure
long hair. Scalp ing
can occur if hair is
not kept away from
tool and ac ces so ries.
Chok ing can oc cur if
neck wear is not kept away from
tool and ac ces so ries.
• Do not lu bri cate tools with
flam ma ble or vol a tile liq uids
such as ker o sene, die sel or jet
fuel.
• Impact wrenches are not torque
con trol devices. Fas ten ers with
spe cif ic torque re quire ments
must be checked with suit able
torque measuring de vic es after
in stal la tion with an im pact
wrench.
• Use only impact wrench sock ets
and ac ces so ries on this tool. Do
not use hand sock ets and
ac ces so ries, as they may be
damaged or cause damage to the
equipment or operator.
• Do not force tool be yond its
rat ed capacity.
• Do not remove any labels.
Re place any damaged labels.
• Use accessories rec om mend ed by
NAPA Professional Air Tools.
10/05/10