Napa 6-1123 Mode D'emploi page 2

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
This insTrucTion Man u al
con Tains iMporTanT safeTy
inforMaTion.
read This
in sTruc Tion
Manual
care ful ly and
un der sTand all in for Ma Tion
Be fore op er aT ing This Tool.
• Al w ays operate, in s pect and
main t ain this tool in ac c or d ance
with Amer i c an Na t ion a l Stan d ards
In s ti t ute Safe t y Code of Por t a b le
Air Tools (ANSI B186.1) and any
oth e r ap p li c a b le safe t y codes
and reg u l a t ions.
• For safety, top per f or m ance and
max i m um du r a b il i t y of parts,
op e r a te this tool at
90 psig, 6.2 bar max
air pres s ure with 3/8"
di a m e t er air
sup p ly hose.
• Always wear impact­resistant
eye and face protection
when operating
or performing
maintenance on this
tool.
• High sound levels can cause
permanent hearing loss. Always
use hearing protection as
recommended by
your employer and
OSHA regulations
while using this tool.
• Keep the tool in
ef f i c ient op e r a t i ng con d i t ion.
• Operators and main t e n ance
per s on n el must be phys i c al l y
able to han d le the bulk, weight
and pow e r of this tool.
• Compressed air can cause
severe injury. Never direct air
at yourself or others. Always
turn off the air supply, drain
hose of air pressure, and detach
tool from air supply before
PLEASE REVIEW ALL WARNING INSTRUCTIONS PRIOR TO OPERATION. SAVE ThIS mAN U AL fOR fUTURE REf ER ENCE.
6-1123
installing, removing, or
adjusting any part or
accessory on this tool,
or before performing
any maintenance
on this tool. Failure
to do so could result in injury.
Whipping hoses can
cause serious injury.
Always check for and
replace any damaged,
frayed, or loose hoses
and fittings. Do not
operate a damaged or worn
tool. Do not use
quick­detach couplings
at tool. See instructions
for correct setup.
• Air­powered tools
can vibrate during use. Extended
exposure to vibration, repetitive
motions, or uncomfortable
positions during use may be
harmful to your
hands and arms.
Discontinue use of tool
if discomfort, tingling,
or pain occurs. Seek
medical advice before
resuming use.
• Place the tool on the work
be f ore start i ng the tool. Do not
point or in d ulge in any horse p lay
with this tool.
• Slipping, tripping and/or falling
while operating air tools can be
a ma j or cause of se r i o us in j u r y or
death. Be aware of ex c ess hose
left on the walk i ng or
work surface.
• K eep body work i ng
stance bal a nced and
firm. Do not over r each
when op e r a t i ng the tool.
• Anticipate and be alert for sudden
changes in motion during use of
any power tool.
• Do not carry tool by the hose.
Pro t ect the hose from sharp
2
ob jects and heat.
• Tool shaft may con t in u e to
ro t ate brief l y af t er
throt t le is re l eased.
Avoid di r ect con t act
with ac c es s o r ies
dur i ng and af t er use.
Gloves will re d uce the
risk of cuts or burns.
• Keep away from ro t at i ng end
of tool. Do not wear jew e l r y
or loose clothing. Se c ure long
hair. Scalp i ng can occur if hair
is not kept away from tool and
ac c es s o r ies. Chok i ng can oc c ur if
neck w ear is not kept
away from tool and
ac c es s o r ies.
• Do not lu b ri c ate
tools with flam m a­
ble or vol a t ile liq u ids
such as ker o s ene, die s el or
jet fuel.
• Impact wrenches are not torque
con t rol devices. Fas t en e rs with
spe c if i c torque re q uire m ents
must be checked with suit a ble
torque measuring de v ic e s after
in s tal l a t ion with an im p act
wrench.
• Use only impact wrench sock e ts
and ac c es s o r ies on this tool. Do
not use hand sock e ts and
ac c es s o r ies, as they may be
damaged or cause damage to the
equipment or operator.
• Do not force tool be y ond its
rat ed capacity.
• Do not remove any labels.
Re p lace any damaged labels.
• Use accessories rec o m m end e d by
NAPA Professional Air Tools.
rev. 12/20/10