Technical Data; Protecting The Environment; Ec Declaration Of Conformity - Black & Decker BEHTS551 Traduction Des Instructions Initiales

ENGLISH
Lubrication oil is available from your BLACK+DECKER dealer
(cat. no. A6102-XJ).
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
After use, carefully clean the blades. After cleaning, apply
u
a film of light machine oil to prevent the blades from rust-
ing.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.

Protecting the environment

Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Troubleshooting
Problem Possible Cause
Slow Dry, corroded blades.
running,
noisy Blades or blade support
or hot bent.
blades.
Bent or damaged teeth.
Loose blade bolts.
8
(Original instructions)
Possible Solution
Lubricate blades.
Straighten blade or blade support.
Straighten teeth.
Tighten blade bolts.
Unit will Lock off not fully
not start. operated.
Cord not plugged in.
Circuit fuse is blown.
Circuit breaker is
tripped.
Cord or switch is
damaged.

Technical data

Voltage V
AC
Power input W
Blade strokes min -
(no load) 1
Blade length cm
Blade gap mm
Blade brake
s
time
Saw blade Max
mm
cut
Weight kg
Level of sound pressure according to EN 62841:
Sound pressure at operator position (L
Sound power (L ) 98.5 dB(A), uncertainty (K) 1.3 dB(A)
WA
Vibration total values (triax vector sum) according to EN 62841:
) 3.8 m/s
Vibration emission value (a
h, D

EC declaration of conformity

MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
BEHTS551 – Hedge Trimmer
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 62841-1:2015; EN 62841-4-2:2019
2000/14/EC, Hedge trimmer, Annex V, DEKRA Certification
B.V. Meander 1051 / P.O. Box 5185
Check that lock off is fully forward
prior to moving main trigger.
Plug cord into a working outlet.
Replace circuit fuse.
(If the product repeatedly causes the
circuit fuse to blow, discontinue use
immediately and have it serviced at a
BLACK+DECKER service center or
authorized servicer.)
Reset circuit breaker. (If the
product repeatedly causes the circuit
breaker to trip, discontinue use
immediately and have it serviced at a
BLACK+DECKER service center or
authorized servicer.)
Have cord or switch replaced at
BLACK+DECKER Service Center or
Authorized Servicer.
BEHTS551
) 87.5 dB(A), uncertainty (K) 1.1 dB(A)
pA
, uncertainty (K) 1.5 m/s
2 2
Type 1
230
650
1840
60
25
<1
35
3.1