Technical Specifications - Marshall MG Série Manuel D'utilisation

MG50CFX / MG101CFX / MG102CFX / MG100HCFX
CLEAN / CRUNCH OD-1 / OD-2
GAIN BASS
0 0 10 10 0 0 10 10
INPUT
1 2 3 4
Rear panel shows MG50CFX combo - MG100CFX combo has the same features
MG100HCFX head is identical except features two loudspeaker sockets
21
1. Input Jack Socket
Jack input for your guitar. Use a good quality guitar
cable (i.e. one that's screened/shielded) to help
prevent noise, interference and unwanted feedback.
2. Gain Control
Controls the amount of signal entering the pre-amp
and the amount of distortion created in the selected
channel.
3. Clean/Crunch Switch
Selects between Clean (green) and Crunch (red)
channels.
4. Bass Control
Adds warmth and low-end depth to your sound.
5. OD-1/OD-2 Switch
Selects between OD-1 (green) and OD-2 (red)
channels.
6. Middle Control
Varies the amount of body in your sound.
7. Treble Control
Increasing the Treble will make your sounds brighter
and more cutting, turning it down will decrease your
tone's edge and make it sound softer as a result.
8. Rev Switch
Switches the reverb effect on and off.
9. Reverb Control
This control lets you add a lush digital reverb to the
selected channel, from a subtle hint to cavernous
and all points in-between. Furthermore, there are two
TAP
MIDDLE TREBLE REVERB VOLUME FX
0 0 10 10 0 0 10 10 0 0 10 10
OFF OFF OCTAVE OCTAVE
5 6 7 8 9 10 11 12 13
22 23
distinctly different sounding reverb types for you to
choose from – Studio or Spring. Studio emulates the
sound of a studio plate reverb while, as expected,
Spring emulates the sound of a classic spring reverb
unit.
10. Volume Control
Controls the volume of the selected channel.
11. FX Switch
Switches the FX section (FX and Delay) on and off.
12. FX Control
Selects and adjusts one of five digital effects - Chorus,
Phaser, Flanger, Vibe and Octave.
13. Tap Switch
Matches the delay FX time to the time between two
pushes. The LED flashes at selected delay time.
14. Delay Control
Controls the amount of signal sent to any one of four
selectable delay types – Hi-Fi, Tape, Multi or Reverse.
15. Ext FX Switch
Switches the external FX Loop on and off.
16. Master Control
Controls the master volume of the amplifier.
17. Damping (Manual) Switch
Switches the power amp damping between classic
amp feeling (LED off) and modern response (LED on).
Holding down the Damping switch for longer than
2 seconds switches the amp between manual and
preset mode (page 6).
4
TUNER
DAMPING
EXT. FX STORE
(MANUAL)
DELAY MASTER
LINE OUT
0 0 10 10
OFF OFF
14 15 16 17 18 19
24
25 26
When using the footcontroller, holding both the
Damping switch and the Store switch will activate the
tuner.
18. Headphone / Line Out Socket
3.5mm headphones / Line out.
19. Store Switch
Stores the current amp settings into the current
channel to recall with the footcontroller. When in
manual mode the Store button lights red.
20. Power Switch
The power switch turns your amplifier on and off. A
channel switch will light up when your amplifier is
turned on and none will be lit when the amplifier is
switched off.
Please ensure the amplifier is switched off and
unplugged from the mains electricity supply before
being moved.
21. Mains Input Connector
Your amp is provided with a detachable mains
(power) lead, which is connected here. The specific
mains input voltage rating that your amplifier has
been built for is indicated on the back panel. Before
connecting for the first time, please ensure that your
amplifier is compatible with your electricity supply.
If you have any doubt, please get advice from a
qualified technician. Your Marshall dealer will help
you in this respect.
The correct value of mains fuse located in the small
drawer at the bottom of the mains socket is specified
on the rear panel of the amplifier. The drawer

Technical Specifications

MG50CFX Combo
Power (RMS)
C hannels
Speaker
Weight (kg)
Size (mm) W, H, D
MG101CFX Combo
POWER
Power (RMS)
C hannels
Speaker
Weight (kg)
20
Size (mm) W, H, D
MG102CFX Combo
Power (RMS)
C hannels
Speaker
Weight (kg)
Size (mm) W, H, D
MG100HCFX Head
Power (RMS)
C hannels
Speaker
Weight (kg)
Size (mm) W, H, D
contains a space for a spare fuse. NEVER attempt to
bypass the fuse or fit one of the incorrect value!
22. Footcontroller Socket
Jack socket for the connection of the footcontroller.
23. Loudspeaker Output(s) Socket
The MG50CFX, MG101CFX and MG102CFX combos
have 1 loudspeaker output. The MG100HCFX head
has 2 loudspeaker outputs.
Always use a non-screened Marshall approved
speaker lead when connecting an extension cabinet
to these amplifiers.
24. MP3 Line In Socket
Jam to your favourite MP3, CD or tape track by
connecting the line out or headphone output of
your player here. Adjust the volume of your player to
match that of your guitar and you've got the perfect
'play-along' practice system.
25. Return Socket
Connect to the output of an external effects
processor or pedal here.
26. Send Socket
Connect to the input of an external effects processor
or pedal here.
5
50W
4
1x12"
16.6kg
518 x494 x278
100W
4
1x12"
20kg
591 x528 x283
100W
4
2x12"
22.4kg
674 x494 x278
100W
4
-
11.4kg
591 x249 x275