Casals CAG90/115 Mode D'emploi page 4

- Use clamps or a vise to secure the object to be worked in
place. The work will be safer if both hands are free to con-
trol the tool.
- Before using the appliance check the disc / tool dimensions
are compatible for this appliance.
- Do not touch any of the appliance's moving parts while it
is operating.
- Do not grind any material containing asbestos. Working with
asbestos and/or silica wheel, the dust produced is harmful for
health. Prevent inhalation of these types of dust by following
the appropriate health and safety regulations.
- Protect yourself from contact with and the inhalation of dust
created by sanding wood and metal surfaces and surfaces
coated with lead paint. Use protective equipment that com-
plies with the appropriate health and safety regulations.
- Exercise precaution after employing the stop operation on
the appliance as the tool will continue moving from the effect
of its own mechanical inertia.
Power tool use and care
- Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
- Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired
- Disconnect the plug from the power source and/or the
battery pack from the power tool before making any ad-
justments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting
the power tool accidentally.
- Store idle power tool out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are dan-
gerous in the hands of untrained users
- Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other con-
dition that may affect the power tool's operation. If dam-
aged, have the power tool repaired before use. Many acci-
dents are caused by poorly maintained power tools
- Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind and
are easier to control
Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account the
working conditions and the work to be performed. Use of
the power tool for operations different from those intended
could result in a hazardous situation.
- Fully unroll the appliance's power cable before each use.
- Do not use the appliance if its accessories are not properly
fitted.
4
- Do not use the appliance if the accessories or consumables
attached to it are defective. Replace them immediately.
- Use the appliance handle/s, to catch it or move it.
- This appliance is for professional use.
- This appliance is not a toy. Children should be supervised to
ensure that they do not play with the appliance.
- Do not expose the appliance to extreme temperatures.
- Do not use separator or reducing bushings, adapters to fix
the discs / tools they are not directly compatible with the ap-
pliance.
- Let the appliance running with no load for 30 seconds in a
safe position. If you notice serious vibration or other defects
stop the appliance immediately. Then check the problem and
/or proceed as we describe on Anomalies and Repair clause.
- Do not operate the angle grinder without the auxiliary handle.
- Always check the workpiece before operation and remove
any obstructions such as nails, staples, screws, string, rags,
cloths and other debris.
- Check the position of power cables before commencing work
ensuring they are well away from the work area.
- When using the angle grinder make sure that the workpiece
is securely clamped to a work bench or vice.
- Before cutting ensure there is a suitable gap below the work-
piece to prevent the disc from touching any obstacles.
- Allow the angle grinder to reach it's optimum speed before
commencing work
- Not recommended for use in conjunction with a cut-off stand.
- Keep hands and other body parts well away from the work
area whist the tool is in use.
- Keep hands and other body parts well away from the discs
while the angle grinder is in use. Do not attempt to remove cut
material whilst the angle grinder is in operation or reach under-
neath for any reason.
- Do not touch the grinding disc after operation. The bit will be
HOT and will burn!
Service
- Have your power tool serviced by a qualified repair per-
son using only identical replacement parts. This will en-
sure that the safety of the power tool is maintained
Any misuse or failure to follow the instructions for use renders
the guarantee and the manufacturer's liability null and void.
Safety Warnings for Angle Grinder
Safety Warnings Common for Grinding, Sanding, Wire
Brushing, or Abrasive
Cutting-Off Operations
- This power tool is intended to function as a grinder,
sander, wire brush or cut-off tool. Read all safety warn-
ings, instructions, illustrations and specifications provid-
ed wit
below
- This
Opera
create
- Do n
signe
Just b
tool, it
- The
to the
sories
apart.
- The
sory m
Incorre
or con
- The
other
er too
mount
vibrate
- Do n
spect
and c
wire b
cesso
dama
cesso
plane
maxim
sories
- Wea
plicat
es. As
glove
abras
be cap
eration
ing pa
to high
- Keep
Anyon
tectiv
acces
area o
- Hold
when
sory m
acces
parts
electri
- Posi