Output W; Rs232 Connector R; Rotel Link T; Ext Rem In Jack Y - Rotel RT-1570 Manuel De L'utilisateur

English
Output
w
Analog Outputs
w
A pair of standard RCA jacks supplies an analog output signal from the
RT-1570 to the source inputs of an audio preamplifier, integrated amplifier,
or receiver.
Select high quality audio interconnect cables. Connect the left and right
channel outputs of the RT-1570 to the corresponding inputs on the preamplifier
or other component.
Digital Output
w
If you are using an outboard D/A converter or other digital processor, you
will need an unprocessed digital data stream from the RT-1570. Using a
standard 75 ohm coax digital cable, connect the RT-1570's digital output
to the digital input connector on the outboard D/A converter.
RS232 Connector
r
The RT-1570 can be controlled via RS232 for integration with automation
systems. The RS232 input accepts a standard straight DB-9 Male-to-Female
cable.
For additional information on the connections, software, and operating codes
for computer control of the RT-1570, contact your authorized Rotel dealer.
ROTEL LINK
t
See Figure 4.
These 2 ROTEL LINK OUT connections can be made with the stereo 3.5 mm
cable (supplied) to a Rotel integrated amplifier and CD player.
These allow the attached Rotel products to communicate with each other
and be controlled via the Rotel Remote App (available for download on
the iTunes store).
®
NOTE: Only the Rotel Link cables supplied with this product should be
used. These 3.5 mm cables have WHITE connector ends and should
not be confused with the 12 Volt Trigger cables that have BLACK
connector ends.
EXT REM IN Jack
y
This 3.5mm mini-jack receives command codes from industry-standard infrared
receivers via hard-wired connections. This feature could prove useful when
the unit is installed in a cabinet and the front-panel sensor is blocked. Consult
your authorized Rotel dealer for information on these external repeaters and
the proper wiring of a jack to fit the mini-jack receptacle.

Internet Radio

What you need before starting

Before you can use your Internet radio, you need the following:
• A broadband Internet connection.
• Connection to the RT-1570 through wired or wireless LAN.
When using the wireless network connection care should be taken to ensure
the RT-1570 and WiFi network are located with strong signal strength. This
helps ensure streaming audio is properly received by the RT-1570. You can
confirm the WiFi Strength under the settings menu. (Settings-->WiFi Strength)

First Time Connection To The Network

When you turn on the unit for the first time, it starts by searching for LAN
connections. If both wired and wireless connections are present, the wired
connection will be the default, unless a "wireless only" selection was made
in the setup menu. The following example illustrates a wireless connection.
Starting ... ...
After a few seconds, it will start to scan for networks.
If no wireless network is found, it will display no network found.
NO NETWORK FOUND
When the RT-1570 finds a Wireless network, the network name (SSID) is
listed on the display. All available wireless networks found by the RT-1570
will be listed.
< MY NETWORK >
It is possible, that your unit will find more than one wireless network, in
which case you can choose which one you want to connect to. Turn the
PUSH SELECT knob 8 on the front panel or use the up/down arrow keys
on the remote control to see the network name for each wireless network
the RT-1570 has found. Press the PUSH SELECT knob
or the ENT key on the remote control to select the desired network name.
If the dispaly shows "Enter WEP key" or "Enter WPA key", then the network
is using encryption. Please obtain the key for the selected wireless network,
or check the user manual of your wireless router for this information. Input
the key to gain access to the wireless LAN.
NOTE: If you would like to use a static IP address, or if the unit can not
automatically get an IP address, then please see the "Network Config"
section under the "Settings" section at the end of the manual.

Selecting A Radio Station

Once the network is properly configured and connected the top-level menu
will be displayed. Please select "Internet Radio", the display will show as:
< Internet Radio >
My Stuff
Media Player
Settings
Now you can select the Internet radio station you want to listen to by turning
and pressing the PUSH SELECT knob
navigation keys on the remote control.
<LOCATION> Enables you to choose radio stations provided in the specific
area and countries:
Africa
< Americas >
Asia
Caribbean
SCANNING NETWORK.. ...
8 on the front panel
< Location >
Genre
Search
SIRIUS XM
8 on the front panel or using the
< XXX1 LIVE RADIO
XXX2 LIVE RADIO
XXX3 LIVE RADIO
XXX4 LIVE RADIO
11
>