Handlebar; Brakes; Pedals; Lights - Bianchi LIF-e e-omnia Manuel D'utilisation Et Maintenance

EN
Before using the pedal-assist bicycle, check that the adjustment screws are tightened as indicated
near them. If there is any doubt about the adjustment, consult an authorized dealer.

2.4.3 HANDLEBAR

The height of the handlebar as well as its inclination can be adjusted by means of the corresponding
adjustment screws. The position of the screws and the modes may vary depending on the model:
E-OMNIA MODEL TYPE
OMNIA FX TYPE (FS) Velomann ST97
E-OMNIA FT TYPE (FT) Velomann ST97
OMNIA X TYPE (HT) Velomann ST97
Velomann Catamaran
OMNIA T TYPE (Tourer)
Man
Velomann Fastback
Velomann Catamaran
OMNIA T TYPE (Tourer)
Lady
Velomann Fastback
Velomann Catamaran
OMNIA C TYPE
(City) Lady
Velomann Fastback
Before using the pedal-assist bicycle, check that the handlebar is aligned with the front
wheel and that the adjustment screws are tightened as indicated near them.
If there is any doubt about the adjustment, consult an authorized dealer.
12
EXAMPLE IMAGE OF HANDLEBAR ADJUSTMENT
SCREWS
1 2
F: R:
3 4
Unscrew 1-2-3-4 to allow rotary movement
1 2
F: R:
3 4
Unscrew 1-2-3-4 to allow rotary movement
1 2
F: R:
3 4
Unscrew 1-2-3-4 to allow rotary movement
1 2
F: R:
3 4
5
Unscrew 1-2-3-4 to allow Unscrew 5 to allow rotary
rotary movement movement
1 2
F: R:
3 4
Unscrew 1-2-3-4 to allow rotary movement
1 2
F: R:
3 4
5
Unscrew 1-2-3-4 to allow Unscrew 5 to allow rotary
rotary movement movement
1 2
F: R:
3 4
Unscrew 1-2-3-4 to allow rotary movement
1 2
F: R:
3 4
5
Unscrew 1-2-3-4 to allow Unscrew 5 to allow rotary
rotary movement movement
1 2
F: R:
3 4
Unscrew 1-2-3-4 to allow rotary movement

2.4.4 BRAKES

All E-OMNIA models are equipped with a disc brake system which can be operated by actuating the
two levers on the handlebar. The right-hand lever operates the rear brake, the left-hand lever operates
the front brake. The braking torque is proportional to the force applied to the levers. You can adjust the
inclination and position of the levers by loosening the lever locking screw.
Before using the pedal-assist bicycle, make sure that the screws securing the brake levers have been
tightened in accordance with the torque indicated on the screws. Adjustment of any other brake system
parameters is not recommended. If there is any doubt about the adjustment, consult an authorized
dealer. Do not touch the brake discs after braking, as they may be hot and this may result in burns.

2.4.5 PEDALS

The pedals must be tightened to the cranks. By applying torque to the pedals, it is possible to apply a
translational motion to the pedal-assist bicycle. All E-OMNIA models are equipped with electric pedal
assist, the motor is automatically activated once the pedal-assist bicycle is switched on and a torque
is applied to the pedals.
The user can fit and remove the pedals ensuring they are tightened to a torque of 22 to 25 Nm.
When assembling, pay attention to the direction of screwing of the pedals: the right-hand pedal
has a right-hand thread, the left-hand pedal has a left-hand thread.
Pedals other than those supplied can be mounted provided that they are in accordance with the laws
of the Country where the bicycle is used.

2.4.6 LIGHTS

All E-OMNIA models have an integrated front and rear lighting system. The reflectors supplied are
required by law in some countries. It is recommended to refer to the national and regional regulations
of the Country where the bicycle is used. Once the switch on button (4) is pressed, the front and rear
lights are switched on and off simultaneously using the control (3) shown in Figure 3 for E-OMNIA
T-Type (man and lady), C-Type, FT-Type models.
Once the switch on button is pressed, the front and rear lights are switched on simultaneously by
pressing and holding for an average time between 1 and 2.5 s the button (6) shown in Figure 4 for
E-OMNIA X-Type and FX-Type models. The lights are switched off by pressing the control (6) for more
than 2,5 s. The inclination of the light beam can be adjusted by means of the adjustment screw shown
in Figure 5.
7
1
2
3
4
6
17
5
6
Figure 3 - Kiox light controls Figure 4 - Purion light controls
EN
2
3
4
Figure 5 - Front lamp adjustment
13