Installing And Removing The Battery Pack - DeWalt DCH416 Guide D'utilisation

English
To Install the Belt Hook
1. Insert the hook into one of the slots, on left or right side,
below the main handle.
2. Install the screw on the underside of the main handle. Be
sure to securely tighten the screw.
To Remove or Move the Belt Hook
1. Remove the screw located on the underside of the
main handle.
2. Pull the belt hook away from the main handle.
3. Insert the hook into one of the slots, on left or right
side, below the main handle, or install the screw on the
underside of the main handle. Be sure to securely tighten
the screw.
DWH200D Dust Extraction System
(Fig. H)
Your heavy‑duty cordless rotary hammer comes with an
adapter for the DWH200D dust extraction system.
The standard SDS Plus tool holder adapter (short) comes
attached in the DWH200D. Your tool requires the included
longer holder adapter.
1. Remove the cross head screw
adapter 21 using a cross head screwdriver (Fig. H).
2. Then use the screw 25
adapter 22 to the dust brush body
3. Slide the newly assembled dust brush
holder adapter 22 into the slot
side handle assembly
4. Connect dust extractor
assembly 20 (Fig. H).
Wireless Tool Control (Fig. A)

CAUTION: Read all saftey warnings, instruction and
specifications of the appliance which is paired with
the tool.
Your tool is equipped with a Wireless Tool Control transmitter
which allows your tool to be wirelessly paired with another
Wireless Tool Control device, such as a D
To pair your tool using Wireless Tool Control, depress the
trigger switch 1 and the Wireless Tool Control pairing button
on the seperate device. An LED on the seperate device will let
you know when your tool has been successfully paired.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.

Installing and Removing the Battery Pack

(Fig. F)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide it
10
25 from the short
to assemble the long tool holder
20 . Tighten securely.
20 and tool
23 on the top of the
6 until you hear an audible click.
24 to the dust brush
WALT dust extractor.
e
7 into the tool handle, align the
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button 8 and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Proper Hand Position (Fig. A, K)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle , with the other hand on the side handle
9
E-Clutch® System (Fig. I)
In addition to the integral (mechanical) clutch, the D
anti‑rotation E‑Clutch® system, offers technology capable
of detecting the motion of the tool. This feature senses
the motion of the tool and shuts it down if necessary. The
E‑Clutch ® indicator LED 16
System is engaged.
Your rotary hammer has an E‑Clutch
indicating the E‑Clutch® (ADC) function. Refer to the table for
more information on LED functionality.
Indicator Diagnosis
OFF Tool is
functioning
normally
SOLID E‑Clutch ®
System
has been
activated
(ENGAGED)

WARNING: Drill may stall if overloaded causing a
sudden twist. Always expect the stall. Grip the drill
firmly to control the twisting action and avoid injury.
SHOCKS® Active Vibration Control
System
For best vibration control, hold the tool as described in
Proper Hand Position and apply just enough pressure so the
damping device on the main handle is approximately mid
stroke. The hammer only needs enough pressure to engage
the active vibration control. Applying too much pressure will
not make the tool actuate faster and active vibration control
will not engage.
D WALT Tool Tag Ready (Fig. A)
e
Optional Accessory
Your tool comes with mounting holes
installing a D WALT Tool Tag. You will need a T20 bit tip to
e
install the tag. Only use the screws provided. The D
Tool Tag is designed for tracking and locating professional
power tools, equipment, and machines using the D
Tool Connect™ app. For proper installation and use of the
D WALT Tool Tag refer to the D
e
6
e
illuminates when the E‑Clutch®
indicator LED 16
®
Solution
Follow all warnings and instructions
when operating the tool.
With the tool properly supported,
release trigger. The tool will
function normally when the trigger
is depressed again and the indicator
light will go out
15 and fasteners for
WALT
e
WALT
e
WALT Tool Tag manual.
e
.
WALT
,