Working With The Power Tool - Flex CSE 55 T Mode D'emploi

Using the guide rail
klqb
tÜÉå=éä~ÅáåÖ=íÜÉ=ë~ï=çå=íÜÉ=ÖìáÇÉ=ê~áäI=
~äï~óë=ìëÉ=íÜÉ=ÖìáÇÉ=ÖêççîÉëK
Inner guide groove ("0"):

mitre angle 0°/-1°
Outer guide groove ("45"):

mitre angle > 0°
Scoring with the guide rail
To prevent the surfaces of board materials
from splintering, they can be scored at a mitre
angle of < 4°.
 Set mitre angle of approx. 4°.
 Set cutting depth to approx. 3.3 mm.
28
 Place saw with the inner guide groove
on the guide rail.
 Score board.
 Set mitre angle to 0°.
 Set cutting depth to full material thickness
plus 3 mm.
 Place saw with the inner guide groove
on the guide rail.
 Saw through full board thickness.

Working with the power tool

`^rqflk>
Ó ^ÑíÉê=íÜÉ=éçïÉê=íççä=Ü~ë=ÄÉÉå=ëïáíÅÜÉÇ=çÑÑI=
íÜÉ=ë~ï=Ää~ÇÉ=ÅçåíáåìÉë=êìååáåÖ=ÄêáÉÑäóK
Ó tÜÉå=íÜÉ=êçí~íáåÖ=ë~ï=Ää~ÇÉ=íçìÅÜÉë=
íÜÉ ïçêâéáÉÅÉI=íÜÉ=éçïÉê=íççä=ã~ó=êÉÅçáäK
klqb
bñÅÉëëáîÉ=ÑÉÉÇ=êÉÇìÅÉë=íÜÉ=éÉêÑçêã~åÅÉ=
çÑ íÜÉ=éçïÉê=íççäI=áãé~áêë=íÜÉ=ÅìííáåÖ=èì~äáíó=
~åÇ=êÉÇìÅÉë=íÜÉ=ëÉêîáÅÉ=äáÑÉ=çÑ=íÜÉ=ë~ï=Ää~ÇÉK=
Sawing along a scribe mark
 Connect extraction hose.
 Set cutting depth to the required
dimension.
 If required, set mitre angle.
 Insert mains plug.
 Switch on dust extraction system.
 Hold the handle with your right hand.
 Place saw bench on the workpiece.
 Push down inspection window as far
as the workpiece surface.
 Switch on saw and wait until the saw
blade has reached the maximum speed.
 Press down saw as far as the stop
of the cutting depth limiter.
 Slowly feed the saw along the material.
klqb
qÜÉ=Åìí=ã~êâë=çå=íÜÉ=ë~ï=ÄÉåÅÜ=ëÜçï=íÜÉ=
éçëáíáçå=çÑ=íÜÉ=ë~ï=Ää~ÇÉ=Ñçê=~=êáÖÜíJ~åÖäÉ=ÅìíK
CSE 55 T