Publicité
Les langues disponibles
Les langues disponibles
Specification
Top wingspan:
approx. 2050 mm
Overall length:
approx. 1020 mm
Total surface area:
approx. 32 dm
All-up weight:
approx. 750 g
Total surface area loading:
approx. 24 g / dm
Dear customer,
Congratulations on your choice of a factory-assembled
model aircraft from the robbe Modellsport range. Many
thanks for placing your trust in us.
The ASW 15 is available in two versions: the ARF model is
fitted with servos, motor and speed controller, while the RTF
model also comes complete with radio control system, flight
battery and charger.
Note: the recommended accessories for the kit version are
not identical to the components supplied in the ARF and
RTF versions. Please note the recommendations in the
instructions.
Very little work is required to prepare the model ready for fly-
ing. You can make it as easy as possible to operate your
new model safely by taking the trouble to read right through
these instructions attentively, together with the separate
information sheets, before you fly it for the first time.
All directions, such as "right-hand", are as seen from the
tail of the model, looking forward.
Suitable adhesives (for repairs)
Use robbe Speed Type 2 cyano-acrylate glue ("cyano") with
the associated activator ("kicker") for all repairs to this
model.
robbe Speed Type 2
No. 5063
Activator spray
No. 5017
Painting, decals
It is not necessary to paint the model.
When applying the decals you can emulate the arrangement
shown in the kit box illustration.
Assembly and operating instructions
ASW 15 ARF, ASW 15 RTF
Essential accessories for the ASW 15 RTF,
Order No. 3195RTF
AA-size dry cell (non-rechargeable)
2
8 cells for transmitter
2
Alternative batteries for rechargeable operation
1.2 V NC cell
8 cells for transmitter
Unicharger 6
Lader 6
Transmitter charge lead
Be sure to read the instructions supplied with the battery
charger and the NC cells before recharging them.
Essential accessories for the ASW 15 ARF,
Order No. 3195ARF
Any robbe-Futaba radio control system with at least four
channels
Y-lead for the aileron servos
or
Two servo extension leads
LiPo battery, 2S 1P, 950 mAh
or
LiPo battery, 3S 1P, 950 mAh
CT-2 connectors for flight battery
Heat-shrink sleeve
Battery charger, e.g. Lipomat 6-800
Essential accessories for flying either version as a pure
glider
1 Switch harness
1 Receiver battery, e.g. 4KR 1100
Replacement parts
ASW 15 tail set
Folding propeller and spinner
ASW 15 wing set
ASW 15 fuselage
ASW 15 decal sheet
ASW 15 canopy
Aluminium hub, 3.0 mm
Glider nose and spacer
Order No.
8008
8004 or 8005
8500 or
8365
F 1415
Order No.
F 1423
F 1419
4827
4828
4077
5150
8478
F 1407
4146
Order No.
31950003
31950004
31950005
31950006
31950007
31950008
31950011
31950010
3
Notes on the building instructions
These building and operating instructions describe both
versions of the ASW 15 model aircraft.
If you have purchased the ARF version, all you have to do is
install the receiver. You can simply skip the description of
the radio control system and the battery charger, which are
intended for the RTF version.
In this case please read the instructions supplied with the
radio control system, the flight pack and the battery char-
ger.
If you have the RTF version, you can skip the following
stage in which the receiver is installed.
The section of the instructions starting with Fig. 13 apply
equally to both versions of the model.
Depending on the version of the model you have purcha-
sed, the servos described and shown in the instructions
may not be the same as those included with your model or
recommended for it.
Preparatory work on the ASW 15 ARF
Fig. 1
Unwind the flexible wire aerial attached to the receiver.
Note: if your radio control system features a six-channel
receiver and mixer functions, the aileron servos can be
connected to two separate channels. In this case you will
need to use two servo extension leads, F 1419, instead of
the Y-lead.
Fig. 2
Apply a strip of Velcro tape to the receiver, and stick the
matching piece in the fuselage.
Pierce a 2 mm Ø hole in the fuselage.
Run the wire aerial through the hole in the fuselage bottom
and out of the fuselage.
Do not deploy the aerial inside the fuselage tail boom.
No. 3195ARF
No. 3195RTF
Publicité
