Introduction; Device Description; Scope Of Delivery; Intended Use - Scheppach HD15 Traduction Du Manuel D'origine

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
we wish you a pleasant and successful working expe-
rience with your new scheppach Scroll machine.
Note:
According to the applicable product liability law the
manufacturer of this device is not liable for damages
which arise on or in connection with this device in
case of:
• improper handling
• non-compliance with the instructions for use
• repairs by third party, non authorized skilled
workers
• installation and replacement of non-original spare
parts
• improper use
• failures of the electrical system due to the non-
compliance with the electrical specifications and
the VDE 0100, DIN 57113 / VDE 0113 regulations
Recommendations:
Read the entire text of the operating instructions
prior to the assembly and operation of the device.
These operating instructions are intended to make it
easier for you to get familiar with your device and uti-
lize its intended possibilities of use.
The operating instructions contain important notes on
how to work safely, properly and economically with
your machine and how to avoid dangers, save repair
costs, reduce downtime, and increase the reliability
and working life of the machine.
In addition to the safety regulations contained herein,
you must in any case comply with the applicable reg-
ulations of your country with respect to the operation
of the machine.
Put the operating instructions in a clear plastic folder
to protect them from dirt and humidity, and store them
near the machine. The instructions must be read and
carefully observed by each operator prior to starting
the work. Only persons who have been trained in the
use of the machine and have been informed on the
related dangers and risks are allowed to use the ma-
chine. The required minimum age must be met.
In addition to the safety notes contained in the present
operating instructions and the special regulations of
your country, the generally recognized technical rules
for the operation of wood working machines must be
observed.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
2. Device description (Fig. 1)
1. Housing complete with motor
2. Undercarriage with wheels
3. Cladding
4. Filter bag
5. Upper clamp
6. Support bar
7. Shavings bag
8. Lower clamp
9. Exhaust hose
10. Clamp 2x
11. Hose coupling
12. Accessory kit
13. Operating instructions

3. Scope of delivery

• When you unpack the device, check all parts for
possible transport damages. In case of complaints
the supplier is to be informed immediately.
• Complaints received at a later date will not be
acknow ledged.
• Check the delivery for completeness.
• Read the operating instructions to make yourself
familiar with the device prior to using it.
• Only use original scheppach parts for accessories
as well as for wearing and spare parts. Spare parts
are available from your specialized dealer.
• Specify our part numbers as well as the type and
year of construction of the device in your orders.
m ATTENTION
The device and packaging materials are not
toys! Children must not be allowed to play with
plastic bags, film and small parts! There is a
risk of swallowing and suffocation!

4. Intended use

CE tested machines meet all valid EC machine
guidelines as well as all relevent guidelines for
each machine.
• The machine has been built in accordance with
state-of-the-art standards and the recognized
safety rules. Nevertheless, its use may constitue a
risk to life and limb of the user or of third parties,or
cause damage to the machine and to othermaterial
property.
• The machine must only be used in technically per-
fect condition in accordance with its designated
use and the instructions set out in the operating
manual, and only by safety-conscious persons who
are fully aware of the risks involved in operating the
machine. Any functional disorders, especially those
affecting the safety of the machine, should there-
fore be rectified immediately. The vacuum exhaust
unit is designed only for removing saw dust (nor for
normal dust).
• Regularly inspect the filter for damage.
• Replace damaged filters!
GB
17 / 120