Skirt Height And Operation Check; Battery Charging - Nilfisk Advance Terra 132B Mode D'emploi Et D'entretien

SKIRT HEIGHT AND OPERATION CHECK

1. With the machine on level and adequate ground to
check the skirt height, activate the brake pedal
(26, Fig. C) (if present), or block the wheels.
2. Turn the ignition key (2, Fig. B) to the "0" position.
Side skirt check
3. Check the side skirt (13 and 14, Fig C) integrity.
Replace the skirts when they have cuts (1, Fig N)
larger than 20 mm (0.75 in) or cracks (2) larger
than 10 mm (0.5 in) (see the "Service Manual" for
Skirt Replacement).
4. Check that the side skirt (13 and 14, Fig. C) height
from the ground is within 0 – 3 mm ( 0-1/8 in) (see
figure O). If necessary adjust the skirt height,
proceeding as follows:
Left skirt:
a. Open the hood, loosen the knob (3, Fig. E)
and remove the main broom access door (1,
Fig. F), lifting upward to disengage the
retainers (2).
b. Adjust the skirt (3, Fig. F) height by loosening
the two screws and using its slots (4, Fig. F).
c. Install in the reverse order of removal.
Right skirt:
a. Remove the Main Broom, as described in the
related chapter.
b. Remove the belt (12, Fig. U) from the pulley
(14, Fig. U); to facilitate the operation, rotate
the pulley (14, Fig. U) by rotating the fan (16,
Fig. U).
c. Remove the screws (25, Fig. C) and the right
cover (24, Fig. C) together with the belt (12,
Fig. U).
d. On the machine, adjust the skirt (1, Fig. S)
height by loosening the two screws (2, Fig. S)
and using its slots.
e. Install in the reverse order of removal.
Front and rear skirt check
5. Remove the main broom, as described in the
related paragraph.
6. Check the front and rear skirts (1 and 2 Fig. Q) for
integrity.
7. Replace the skirts when they have cuts (1, Fig N)
larger than 20 mm or cracks (2) larger than 10 mm
(see the "Service Manual" for Skirt Replacement).
8. Verify that:
– the front skirt (1, Fig. P) drags lightly on the
groung (like in Figure P) and that it raised off
the ground.
146 0791 000(2)2004-02
– the rear skirt (1, Fig. O) must have an height
from ground from 0 up to 3 mm (0.1 in) (like in
Figure O).
9. If necessary, adjust the skirt height by loosening
the four screws and using its slots (3, Fig. R).
10. Pulling on the front skirt lifting lever (27, Fig. C),
verify that the front skirt (1, Fig. Q) rotates upward
approximately 90° (like in Figure Q). Release, the
lever and verify that the skirt returns to its initial
vertical position and does not remain slightly
elevated. If necessary, see the Service Manual for
adjusting or replacing the skirt lifting cable.
11. Install in the reverse order of removal.

BATTERY CHARGING

WARNING!
Battery charging
hydrogen gas. Charge the batteries only
in a well-ventilated area and far from open
flames or sparks.
Do not smoke during battery charging.
Keep the hood open while recharging the
battery.
WARNING!
Pay attention during battery recharging
because there can be battery liquid leaka-
ge. The battery liquid is corrosive. If it co-
mes in contact with the skin or eyes rinse
thoroughly with water and consult a phy-
sician.
1. Drive the machine on level ground and activate
the brake pedal (26, Fig. C) (if present),or block
the wheels.
2. Turn the ignition key (2, Fig. B) to the "0" position.
3. Open the hood (7, Fig. C).
4. Only for lead-acid batteries, check the correct
level of electrolyte inside the battery; if necessary,
fill through the caps (8, Fig. U) to the required
level.
5. Leave the caps (8) open for the next recharging.
6. Clean (if necessary) the upper surface of the
battery.
7. Connect the battery charger electrical cable (5,
Fig. U) to the electrical supply (the system voltage
and frequency must be compatible with the
battery charger: see the Battery Charger Manual).
8. When the green warning light (11, Fig. U) turns on,
the battery is charged.
OPERATOR MANUAL
produces explosive
11