Battery Charger; Accessories; Documentation; Installation And Coupling - Klaxon KLICK HYBRID Manuel D'emploi

D. TETRA CONNECTOR (
WITH DETAIL OF PATENTED
Figure 9 illustrates a TETRA CONNECTOR and identifies the elements that make it up.
1. Velcro grip of CONNECTOR
2. Mounting system in the CROSSBEAM (with ball-type lock)
3. Easy release lever of the KLICK device
4. KLICK® coupling (Patent Pending)
5. Seat of upper pin
6. Seat of lower pin.

9.3 BATTERY CHARGER

Figure 10 shows the battery charger that is supplied with the POWER battery (11 Ah), which are compatible with the Hybrid model.

9.4 ACCESSORIES

KLICK can be equipped with various accessories. You may need to consult the appropriate User's Manual (ask KLAXON or visit our
website: www.klaxon-klick.com) for some of them.

9.5 DOCUMENTATION

This USER's MANUAL is provided with the Device in printed format and must be stored with the utmost care. If you lose the above
documents, request a copy of them in writing to KLAXON.

10. INSTALLATION AND COUPLING

10.1 INSTALLATION

KLICK devices are provided by KLAXON (or by an authorised technician) only after having pre-installed the coupling set on the

wheelchair.

10.2 COUPLING STEPS

During the entire coupling operation, stop in a flat area, as free as possible from uneven ground and away
from hazards which could cause personal injury.
•
Insert the CROSSBEAM in one of the two CLAMPING RINGS and secure it by inserting the specific PIN (Figure 11).
•
Insert the CROSSBEAM also in the second CLAMPING RING and secure it by inserting the specific PIN (Figure 12).
Note: The CROSSBEAM can always remain installed on the wheelchair; if necessary (for loading and unloading from vehicles
and closing the folding wheelchair) it can be removed and placed in a safe place.
•
Insert the CONNECTOR in the square seat of the CROSSBEAM, pressing the lever located on its bottom. Once inserted,
release the lever and make sure that the CONNECTOR is securely locked (Figure 23).
•
After having inserted the CONNECTOR, the device will be as shown (Figure 14).
•
To secure the KLICK device to the connection, move the wheelchair into position as shown (Figures 15 and 16). Make sure
the opening of the coupling is placed over the upper pin (Figure 17).
•
Maintaining the position, activate the brakes of the wheelchair and grip the pedal cranks at the centre, near the point of
insertion with the movement of the steering wheel; lift the KLICK device until the upper pin is fully inserted in the opening of
the coupling (Figure 18).
At this point, continue to raise the handlebar by pushing it forward until the lower pin is fully engaged with the connection;
at that point the safety button is triggered (Figure 19).
CAUTION!
Once the device is connected to the wheelchair, it is important to ensure that:
•
The ground clearance of the front wheels of the wheelchair is 4 cm (with the wheelchair empty - Figure 20).
•
The kickstand is located above the line of the front wheels and placed below the footboard, so as not to interfere with it
(Figure 21).
If these requirements are not met, never use the device for any reason and immediately contact an
CAUTION
authorised KLAXON service centre.
10.3 WHEELCHAIR
KLICK devices can be installed only on compatible wheelchairs. KLICK products must be only be installed by authorised KLAXON
technicians who may decide, under their own responsibility, if the specific wheelchair can be properly used with the KLICK device.

11. KLICK HYBRID VERSION OPERATION

11.1 USER INTERFACE

The device is equipped with a multifunction LCD display, used to switch the device on and off, select the maximum speed and
display several operating parameters (Figure 22).
•
The icon located top left (1) shows the current battery charge level.
•
The number (2) in the centre of the display shows the speed, in km/h.
KLICK Hybrid User's Manual (ENG) - rev.01 of 30.06.2018
KLAXON Mobility Gmbh – ENG
"KLICK® ")
SYSTEM
8