Güde MD 1700 Traduction Du Mode D'emploi D'origine page 11

Caution! Sparks may reach inflammable material even if
•
it is covered up.
Blocking the blade will result in a permanent reactive
•
power. If that is the case, switch the unit off.
Caution! The discs will run out after switching the unit
•
off. Do not expose the discs to lateral pressure.
The unit is allowed to be operated with a dust-
•
exhausting device only. In addition, use a breathing
mask. The dust exhauster must be approved for
exhausting stone dust.
Unit may be operated on the mains with stray
current protection.
Emergency Action
Apply the first aid adequate to the injury and get qualified
medical assistance as quickly as possible. Protect the injured
person from more accidents and calm him/her down.
Assigned Use
The unit is designed for cutting dividing or expanding joints
without the use of water in mineral materials – masonry in the
first place – being firmly supported with a guide bar.
The manufacturer should not be held liable for any personal
and material losses due to a failure to observe these rules.
Residual Hazards and Protective Action
1. Electrical Residual Hazards:
Direct electrical contact:
•
Defective cable or plug may cause an electrical
shock.
Have the defective cable/plug exchanged by a
professional. Use the unit only if connected via a stray
current switch (FI).
2. Mechanical Residual Hazards:
Cutting, incision:
•
Diamond disc edges may cause incisions.
Wear protective gloves when working with the unit.
Catching, winding:
•
Lose garments and jewels may be caught with
moving parts
Always wear tight-fitting garments and no jewels that
could be caught
Friction, abrasion:
•
Touching the rotating blade may cause severe
accidents.
Never touch the disc when it is moving.
3. Thermal Residual Hazards:
Burns, frostbites:
•
Temperatures generated on the disc at work are
very high.
Let the disc cool down before touching it. Always
wear protection gloves.
4. Noise Hazard:
Hearing Impairment:
•
Prolonged work with the unit may result in
hearing impairment.
Wear ear protectors
5. Vibration Hazard:
Use of manually operated tools:
•
Prolonged work results in muscular strain, which
results in a risk of injury.
Have breaks at certain intervals, the intervals may
differ according to the user.
6. Radiation Hazard:
Laser radiation:
•
The unit has a laser to indicate the cutting line.
Laser may affect the retina.
Never look directly in the laser beam.
7. Materials and Other Substances Hazards:
Contact, aspiration:
•
Lungs may be affected by great amount of dust
being formed
Always wear breathing mask.
8. Human Factor Neglect:
Neglect us of personal protection equipment:
•
Operating the unit without adequate PPE may
cause severe external/internal injuries.
Always wear prescribed protective clothing and work
considerately.
Inadequate local lighting:
•
Insufficient light is a heavy safety risk.
Provide for sufficient lighting
9. Other Hazards:
Breaking in the course of operation:
•
Defective discs may break in operation and cause
the user a severe injury.
Check the discs for damage at regular intervals.
Never use damaged discs. Always wear
corresponding protective clothing. .
Thrown away objects and splashes:
•
During cutting, your eyes may be injured with
particles of the disc or medium splashes.
Always wear goggles when working with the unit
Disposal
Instructions for disposal arise from icons placed on the
appliance or its package. The description of individual
meanings can be found in the "Marking on appliance".
Requirements for operating staff
The operating staff must carefully read the Operating
Instructions before using the appliance.
Qualification
Apart from the detailed instructions by a professional, no
special qualification is necessary for appliance using.
Minimum age
Persons over 16 years of age can only work on the appliance.
An exception includes youngsters trained in order to reach
knowledge under supervision of the trainer during
occupational education.
Training
Using the appliance only requires corresponding training by a
professional or the Operating Instructions. No special training
is necessary.
Technical Data
Supply connection:
Frequency:
Protection class:
Max. output:
Speed:
Power cable:
Disc diameter:
Cutting depth:
Cut widths (mm):
Acoustic output level:
Weight ca:
Ordering No.:
11-GB
230 V
50 Hz
ll
1700 W
-1
4000 min
1,8 m/H05 VV-F
150 mm, Bore 22 mm
40 mm
2,5 / 6 / 14 / 19 / 29
95 dB (A)
4,1 kg
58090