Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Product Information
Brand
August Home Inc.
Product Name
View Doorbell Cam
AB-R3
Model
Software Version
RC17
Hardware Version
04
Manufacturer
August Home, Inc.
Information
657 Bryant St.
San Francisco, CA 94107
(FCC, IC /CE /RCM)
Battery Information
Risk of explosion and personal injury if device is installed
into non compatible circuit. Do not open, mutilate, or
expose to conducting materials (metal), moisture, liquid,
fire or heat above 60° C (130° F), incinerate, or immerse
in water or liquid of any kind. Do not short circuit. Doing
so may cause batteries to leak or explode, resulting in
personal injury.
You assume all risk associated with the suitability, instal-
lation and performance of the doorbell and other third
party components, hardware, software and services that
you select.
FCC Compliance Notice
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni-
cian for help.
This device complies with part 15 of the FCC Rules. Op-
eration is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved
by the party responsible for compliance could void the
user's authority to operate the equipment.
Device Information
Operating Frequency Band (RF):
WIFI: 2412~2472 MHz(2.4GHz)
BLE: 2402~2480MHz (Tx & Rx)
433M: 433.92MHz
5G WIFI:
FCC: 5150 ~ 5850 MHz (5.8GHz)
IC: 5470 ~ 5600MHz, 5650 ~ 5725MHz, 5725 ~ 5850MHz
CE: 5470 ~ 5850 MHz
Modulation mode:
BLE: GFSK
2.4GHz WIFI: DSSS, CCK, BPSK, QPSK, 14QAM, 64QAM
5GHz WIFI: BPSK, QPSK, 16QAM, 64QAM
433M: FSK
Max. Of Transmit power (CE):
2.4G WIFI: 17.73dBm
5G WIFI: 13.91dBm
BLE: 4.64dBm
433M:8dBm
Maximum of Antenna's Gain:
WIFI: 0.1dBi (2.4G) 1.0dBi(5.8G)
BLE: 0.1dBi
433M: -0.5dBi
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncon-
trolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This Class B digital apparatus complies with
Canadian ICES-003
The device is compliance with RF exposure guidelines, users can obtain Canadian
information on RF exposure and compliance.The minimum distance from body to use
the device is 20cm.
This device complies with Innovation, Science, and Economic Development Canada's
licence-exempt RSS standard(s). Operation is subject to the following two condi-
tions:(1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
CAUTION: Risk of fire, explosion, or burn. Do not short circuit, crush, heat above 60°C,
incinerate, or disassemble the battery. Follow manufacturer's instruction.
Battery Changing Instructions
1.
Remove the doorbell cam from the wall mount by sliding up and off the mount.
Make sure to loosen the retaining screw first if necessary.
2.
On the back of the doorbell, press the metal release tab on the battery. Firmly
grip the battery and slide down, removing it from the doorbell body.
3.
Charge the battery if needed by plugging into a USB charger using the included
USB cable. Remove from charger when fully charged.
4.
Replace the battery by inserting into the doorbell cam with the metal release tab
at the back. It will snap into place when fully inserted.
16
Publicité
Table des Matières
