Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
BUILT-IN IRONING CENTER
READ AND SAVE THESE INSTRUCTIONS
WARNING
AVD45 and AVD50 Series Only
ALL ELECTRICAL WORK MUST BE DONE IN ACCORDANCE WITH
LOCAL AND/OR NATIONAL ELECTRICAL CODES AS APPLICABLE. FOR
SAFETY, THIS PRODUCT MUST BE GROUNDED. IF YOU ARE UNFA-
MILIAR WITH METHODS OF IN STALLING ELECTRICAL WIRING, SE-
CURE THE SERVICES OF A QUALIFIED ELECTRICIAN.
The ironing center should be installed on a SEPARATE 15 amp circuit to
prevent circuit overload.
TURN OFF POWER AT SERVICE ENTRANCE BEFORE INSTALLING
WIRING OR SERVICING THIS PRODUCT.
1. Do not place EXCESSIVE WEIGHT (weight should not exceed 30 pounds)
on the ironing board when opened as it is designed to accept normal ironing
use only.
2. Allow iron to cool down before storing in the cabinet.
3. Empty water reservoir and turn off steam action prior to storing iron.
4. Turn power off when not in use.
5. Do not remove the board retainer.
6. The appliance is supplied with approved components and wires which must
not be changed. If any components or wires of this equipment is damaged,
it must only be replaced by the manufacturer, service agent or similarly quali-
fied person in order to avoid hazard.
7. This unit may be installed as a surface mount. If installed in this manner, you
MUST USE the Surface Mount Collar Assembly (AVDSMN). See instruc-
tions included with Assembly, for mounting by this method.
INSTALLATION
1. DETERMINE WALL OPENING.
The Broan Ironing Centers are designed to fit between standard 16" on-center
wall studs. A 49-1/4 " x 14-1/8 "x 3-7/8" deep opening is required. 24" on-center
studs will require framing to proper opening size.
2. DETERMINE DISTANCE ABOVE THE FLOOR.
Use the following chart to determine the recommended wall opening above the
floor:
Wall Opening
Above the Floor
AVD40/45 Series
24"
28"
30"
32"
3. ATTACH CLEATS.
Fasten 2x4 cleats to wall studs to provide a level surface on which to rest
cabinet.
4. MOUNT CABINET.
Lift cabinet into place and attach it to studs using the six supplied screws.
Mounting holes positions are indicated by the arrows. On AVD45 and AVD50
Series models, remove the wireway cover to access mounting hole. Be sure to
allow for wall covering thickness behind cabinet face frame. Plumb and shim
cabinet to fit.
5. CONNECT WIRING (Fig. 2)
Remove wireway cover. Bring house wiring into cabinet access hole and attach
wiring to cabinet with an approved wire strain relief. Connect black to black,
white to white and green/bare wire from house wiring to ground fixing terminal
at the top end of the cabinet. Replace cover.
®
(Fig. 1)
Working Height
AVD50 Series
30"
29"-31"-33"
34"
33"-35"-37"
36"
35"-37"-39"
38"
37"-39"-41"
(AVD45 & AVD50 Series only)
MODELS AVD40B • AVD40KB • AVD40WB
AVD45B • AVD45KB • AVD45WB • AVD50B
Fig. 1
CAUTION: DO NOT ALLOW WIRE TO EX-
TEND OUTSIDE OF WIRING BOX. EX-
POSED WIRES CAN BECOME PINCHED
AND ELECTRICAL SHOCK HAZARD MAY
RESULT.
Fig. 2
Page 1
Publicité
Sommaire des Matières pour Broan AVD40B
- Page 1 Fig. 1 1. DETERMINE WALL OPENING. The Broan Ironing Centers are designed to fit between standard 16” on-center wall studs. A 49-1/4 ” x 14-1/8 ”x 3-7/8” deep opening is required. 24” on-center studs will require framing to proper opening size.
- Page 2 (Fig. 4) NOTE: Door and fixtures are supplied on AVD40WB, AVD40KB, AVD45WB, and AVD45KB. Decorative door and fixtures may be purchased separately for AVD40B, AVD45B and AVD50B models. (See Service Parts List) Fig. 4 1. MOUNTING THE CABINET DOOR Door may be hinged from either side of the cabinet. Both sides of the cabinet has pre-punched holes.
-
Page 3: Unité De Repassage Integré
(Fig. 1) 1. DETERMINEZ L’EMPLACEMENT DANS LE MUR. Les unités de repassage Broan sont prévues pour être installées entre les montants standards Fig. 1 (16inches ) au milieu d’un mur. Une ouverture de 49-1/4“ x 14-1/8“ x 3-7/8” est nécessaire. Les montants centraux de 24"... -
Page 4: Réglage De La Hauteur De La Planche À Repasser
NOTE: La porte et les fixations sont fournies avec le modèle AVD40WB, AVD40KB, AVD45WB, and AVD45KB. Portes décoratives et fixations peuvent être achetées séparément pour les modèles AVD40B, AVD45B, et AVD50B. (Voir la liste des pièces d’entretien.) 1. MONTAGE DE LA PORTE DU MEUBLE Fig. - Page 5 REQUERIDA EN LA PARED. DEL GABINETE Los centros de planchado Broan han sido diseñados para ser montados entre vigas separadas por una distancia de 16 pulgadas. Una cavidad de 49-1/4” x 14-1/8” x 3-7/8” de profundidad es necesaria. Para vigas separadas por una distancia de 24 pulgadas, se requiere agregar otra viga que permita tener una cavidad de 16 pulgadas.
- Page 6 MODELOS MODELS AVD40B • AVD40KB • AVD40WB AVD45B • AVD45KB • AVD45WB • AVD50B ® Page 6 INSTRUCCIONES DE USO (Fig. 3) ENCHUFE Consola de control (Series AVD45 y AVD50) INDICADOR LUMINOSO INTERRUPTOR DE SEGURIDAD INTERRUPTOR DE SEGURIDAD La mesa de planchado oprime este switch cuando es colocada en la posición vertical (al ser guardado).
-
Page 7: Service Parts Diagram Diagrame De Pièces De Remplacement Diagrama De Piezas De Servicio
MODELS / MODÈLES / MODELOS MODELS AVD40B • AVD40KB • AVD40WB AVD45B • AVD45KB • AVD45WB • AVD50B ® Page 7 SERVICE PARTS DIAGRAM DIAGRAME DE PIÈCES DE REMPLACEMENT DIAGRAMA DE PIEZAS DE SERVICIO 50 & 51 AVD50B AVD45KB AVD45WB... - Page 8 MODELS / MODÈLES / MODELOS MODELS AVD40B • AVD40KB • AVD40WB AVD45B • AVD45KB • AVD45WB • AVD50B ® Page 8 AVD50B AVD45KB AVD45WB AVD45B AVD40KB AVD40WB AVD40B DESCRIPTION / DESCRIPCIÓN 99523915 99523915 99523915 99523915 ------------- ------------- ------------- Silent timer...